I've recently put a Turn Off-Road hardtop on my vehicle and no longer need the OEM soft top. It has 2.5 years of wear on it. I'll throw in a Bestop Bimini Mesh shade as well. Comes with the necessary trim pieces and bracketry. I have it zip tied shut currently. Some of the material on the inside...
Howdy folks, thought I'd share my experiences here, in case other folks run into similar issues. I have a 2021 4D Badlands, its been good to me up until about 34,000 miles.
What I'm experiencing right now, is similar to something that has happened to me once before early into ownership. The...
Anybody use a Diono Radian 3R in the back seats? They’ve got a great reputation for 3 across configurations.
When I move my son’s Clek car seat into my Bronco the frame pushes the seat so far high and forward little dude can damn near kick the back of my head.
I was watching this video last night about the new bits on the Taco:
Right at that point i was like hey, I've seen that before. Surely thats nearly identical to the HOSS 2.0?
Howdy,
Hoping someone can help me out. I want to dig into where the 2.4Ghz Wifi and Bluetooth antenna locations are. I know the LTE antennas are under the dash trim right in front of the windshield, but nothing in the manuals seems to help me understand where the 2.4Ghz antennas are. I've...
I picked up the MetalCloak front bumper a couple weeks ago and have been patiently waiting to install. I pulled a Warn EVO 10S off a Jeep JL from a friend and so this weekend with not too much commitments I got after it.
Removal of the OEM bumper, I would say you should commit about 2 hours to...
Heavy Duty Modular Bumper and skid plate taken off a 2021 Ford Bronco Badlands. The parking sensors and wiring harness have been removed, though I do have plugs to cover the sensor holes. Also included is KR Off-Road fog light pocket mounts. The plastic covers that go near the recovery hooks are...
I've seen a few remarks here and there about bolt-on winch plates bending. I'm trying to decide if I want to swap my modular bumper out for one with an integrated winch mount, or just do a bolt-on. Personally I like the look of the OEM modular, and my plan was to grab a winch mount for it. Here...
Up for sale is a Raket Designs roof rack for a 4-Door Bronco. Works with both soft-top and hard-top. I had it installed on a soft-top and found the wind noise to be a bit much and since this is my daily driver I'm not willing to keep putting up with it. I also put my top down ALOT so I jumped...
So three times now I've been up to Big Bear (~7000ft) in the cold, before leaving my windshield washers dispense just fine. At some point during the climb up the mountain, they stop working, and will only start working again if you add a bit of fluid even though it's still quite full.
Any...
A while back when I installed my ARB compressor in the engine bay, I was going to use an add-a-fuse to send power to the switch to light it up. I purchased an add-a-fuse on Amazon of the proper amperage, but when I went to install it, it was too big or too small I can't remember which. This got...
I'm hoping someone who has torn into the aux switch area can help me out here. I want to relocate my Yaesu 400 control panel up near the AUX switches using a 3D printed bracket a friend is willing to create for me. My though is to use a combination of 3M adhesive tape with adhesion promoter, and...
Used ARB portable air compressor. Great for up to 35s (though those are a little slow). It will probably struggle with 37s and above.
Local Pickup in San Marcos, CA (North County San Diego) and I travel up to Orange County usually once a week.
A more recent photo will be forthcoming. I removed this from my 4DR badlands. The top of the drawer has some wear from use, but I think it’s anyone’s best interest to add a carpeted piece of plywood to this anyway. I highly recommend leaving the dividers out of the drawer but I will reinstall...
My Yaesu 400 remains located here:
After 9 months of it in this spot, I think I'd like to relocate it. It's partially in the way. of the glovebox, and not all that comfy for the passenger either. I use a remote speaker mounted to the 67D rail on the dash, so I'm not worried about the audio...
I had a great time last week with Camp4LO for the 4LO Fiesta in San Felipe. I was the only Bronco out there. I stuck with the easier rides, but definitely still had a ton of fun. Crossing the border absolutely got me out of my comfort zone a bit, especially since I missed the convoy down. Turns...
I'm heading down to San Felipe in Baja this Thursday with Camp4Lo. I'd been putting off rotating my wheels a little longer than I should and punched through some procrastination today and got to it. When I got to the last wheel, I discovered the zip tie for my fog light wiring harness had broken...
I shot this picture a couple weekends ago at the SoCal Broncos meetup. I'm using it as a wallpaper on a 21:9 ratio ultra-wide desktop monitor. I can imagine it would like fine cropped on a standard 16:9 screen as well.
Has anyone installed the JCR overhead panels? I am debating adding these eventually, with plans to relocate my Yaesu control panel. I also just removed my Bimini Mesh in exchange for a Jtops USA mesh. Its amazing how much better it looks from the inside now that there aren't lines for zippers...
$100 local pickup to San Diego or I am in Orange County Tuesdays and thursdays.
OEM Bimini Mesh top, made by bestop. 10,000 miles or so on it.
I don’t think I saved the bolts and washers to install on a vehicle that isn’t prepped for a hard top.