Search results

No regrets yet, and I like my script Bronco (although this one is factory)

see upper right

Yeah Mad Matt is a good role model. Thanks for sharing your story and glad you’re ok. Hope to see you on the trails!

Below is based on advice from Madmatt4WD and others. Recovery Hierarchy Checklist Minimal risk: Shovel, track building, vehicle prep (tire pressure lower, 4x4 low engaged, lockers on) Reduced risk: Recovery boards Low risk: Tow (zero kinetic) can still use a kinetic rope/strap, but just a...

How are you liking the Greenlane aluminum steps?

I used the Bracketeer for an under-seat install, and it’s been very solid so far. Initially, I had my doubts, but another Bronco owner told me it worked well for him. He gave me a couple of installation tips that I’ll share below. Tip #1: The Bracketeer has two set screws that help secure the...

I like all of my mods so far - mostly thanks to lots of good advice from pouring over the bronco6g forums.

SOLD on 1/5/2024 for $300 Brand new uninstalled Factory Steel Skid Plates with bolts: Lower Engine and Front Bumper (modular) plates, plus six new mounting bolts. Came as part of the factory kit and I only needed the gas tank and T-Case plates. Some small shipping scuffs - see photos. $300...

**** SOLD **** BN uninstalled Factory Steel Skid Plates: Lower Engine and Front Bumper (modular) plates. Came as part of the factory kit and I only needed the gas tank and T-Case plates. Some small shipping scratches - see photos. $300 OBO for Front and Engine skid plates pictured. Prefer...

Yes. Purple wire coming out of compressor switch loom connector tied to Aux switch. If you're using pressure control, you can also tie the PCM red wire to the same Aux switch. I ran PCM red to a single WeatherPack connector near the compressor connectors. Then I used extra PCM red wire to run...

I used the 1.5m (4.92ft) ARB steel braided hose - most ARB vendors carry it. I did a test routing using a flexible tape measure to estimate the size I needed - you should probably do the same based on your desired routing. I might have been able to get away with 1m with a more direct routing...

ARB support's response was as noted in my previous post: From ARB Support: "That rivet is no longer utilized while using the ARB compressor mount. The DCLM is relocated onto the compressor bracket and the OEM bracket is no longer needed." Others have installed the mount and not reported any...

Aman-Thanks for sharing your install - it was helpful. I just finished installing an ARB Twin with ARB Pressure Control. Some photos below. I did a few things differently - not better or worse, just different - hope this helps others. I wanted both an input and an output port on the vehicle...

For the ARB Twin, any thoughts/pros/cons of alternative mounting orientations of the compressor on the bracket? Installation manual shows electrical connections towards engine with air filters facing outside over the computer module. I've seen a few others mounted with electrical connections on...

I also have given up on the ARB mount. Uninstalled it and purchased the KR Off-Road mount. FYI The alternate DLCM position I previously proposed would not work for me due to too short DLCM cable length. ARB support's response to the unsupported wheel liner concern was: "That rivet is no longer...

Thanks for the response. I looked at the AAL tailgate mount - looks good, but in my case I want the twin compressor, with the option of adding the manifold, and I don't want it mounted inside the vehicle. IMO the ARB bracket addresses those requirements the best. I haven't found the ARB mount...

I'm in the midst of this installation on a 2.7L. I might be too late to help you, but maybe you can let me know what you ended up doing. For your question 1: The white clip and rubber plug that holds the clip to the body does in fact need to be relocated on my 2.7L. The instructions later say...

Having secured all of the parts, I'm planning to install the ARB mount in the coming weeks. ARB's mount design and build looks very robust, and I like where it positions the compressor vs. other vendor's designs. A few things I'm planning to do differently: 1) Omit the manifold and instead...

Thank you!

Thank you!