Search results

LED Lights can cause this issue. Are you at the same place when this happens? If you have any after market LEDS on when this happens? LED lights in your garage?

If the Peg itself is broken, I would treat it like a woodworking problem. Fit the peg parts back together, if they can be reassembled with out any big gaps you are in luck. Clean each side of the parts with denatured alcohol. Get a good plastic glue (Gorilla glue) Wet one side of the part...

I would not use Muratic Acid unless you are outside and no other metal is around you. I used this on my garage floor to clean it and do an acid wash before I put down epoxy. Any metal that was left in my garage rusted because of the fumes. Use Corrseal, you brush it on it turns the rust black...

Got a picture of how you mounted your MXT 575 to it. I have been looking at a better place then behind the glove box.

Sorry I thought you meant the rubber seal at the top of the window.

If the shock rusted and fell apart, how is that a Ford issue? Did Ford make the shock? All OEM's send out a specification to other MFG's for parts. In this case shocks. Billistien built the shocks and certified they meet the OEM spec. The shock failed not the mount or anything Ford built...

I put a little on a paper towel or shop towel. A little goes a long way. I do al the door seals as well as the hard top seals maybe twice a year.

Use Sil Glyde on the seals. It will keep them from freezing. Sil Glyde

Super Clean the windshield. Then the wipers. Yes this works no you won't scratch the glass. 1 Grab 0000 steel wool and scrub all the outsides of the windows use circular motion 2 Grab the Rain X concentrate and apply it to a folded blue paper towel and apply in a circular motion 3 Repeat...

What does the screen look like when it cuts out? Does the volume just stop or the radio go blank?

What does the radio do? My wife and I both have I-phones, and we don't have any issues yet. Does it go to the phone looking for a Bluetooth source (Pandora, Iheart radio or Apple Music). I would try deleting just one phone, then hope in and drive listening to a radio station, shut off the...

As for them not hearing the sound. I had a 2007 Explorer with a suction sound coming from the dash area (like a vacuum hose off sound). My SW sent the best Tech to ride with me and listen to the sound. I get going and the sound started, I asked the tech if he could hear it. He looked right...

Fixed it. This is his concern so maybe this will help figure it out.

I just found this SSM. SSM 51673 2021-2023 Bronco - Trailer Connected Message Displayed In The IPC When No Trailer Is Connected - Workshop Manual Updates Some 2021-2023 Bronco vehicles may exhibit a warning message displayed in the instrument panel cluster (IPC) that there is a trailer...

This is going to sound stupid, but hey I am going to say it. Take you antenna off and see if goes away. Also check the piece that attaches to the fender use painters tape. If not the Ant. Painters tape around hood gaps. Painters tape around around end seems. Last would be door seems. Mike

Going to sound stupid, but do you have the tow package? If so do you have anything plugged into the 4 or 7 pin plug? I would start by just cleaning the connectors in the rear. After that I got nothing.

Most likely it is not bad it is doing its job (the BMS). The only way I know to check for any current draw is. Connect Amp meter to positive lead and he battery positive terminal. An amp clamp may work for this but it is not as accurate. Turn off all electronics Leave hood open, but close all...

How much do you drive it? I have found on my F150 and my Bronco if I just go back and forth to work in about two weeks I will get the same message. I now take it for a 30 or 40 minute drive once in a while or toss a battery tender on it when I know I won't drive it enough. It is the BMS that...

Well let's stat with any after market electronics, Lights winch etc? Your best bet is to get an AMP meter and place it in line with the positive lead from the battery. Start pulling fuses until the current drops. Chase that line. Would I consider this a lemon? No I would not myself...

I really doubt it was the power cord. First there are no marks on the cord. Second the cord if it did get that hot would be brown. Third how long would it have to have been sitting in the same position to cause this. The plastic on the interior seems to scratch pretty easy. Do you wear a ring...