2022 Outer Banks Eruption Green Build

[rguest3]

I did not get any pictures yet of the Bronco after it was finished getting the suspension installed. Here it is getting Aligned and Tire/wheel mounted.

Wheel Alignment, RTR Tire Carrier

Icon Compression Wheels - 18x9 - +25, Titanium - Toyo ATIIIs - 37x12.50x18

Sponsored

 

[rguest3]

I finally took some pictures after installing the New Icon Suspension and Tires and Wheels. I love the way this Bronco drives! I just drove it back to Florida from Virginia. Excellent road manners with no issues what so ever.


37x12.50x18 Toyo ATIII and Icon Compression Titanium 18x9
RTR Spare Tire Mount - VERY Stout compared to Stock.

RTR Grill
Baja Designs LP6s and Corner Pocket Fog Lights

Minimal Tire outside of Sasquatch Fender flares - +25 wheels with 3/4" Spacer = +6 Overall

I already have a Hard Top in my shop now. I will have the Hard Top and Fender Flares painted Eruption Green and then install the JCR Roof Rack. Almost done, I think?

 

[JonDW29]

I finally took some pictures after installing the New Icon Suspension and Tires and Wheels. I love the way this Bronco drives! I just drove it back to Florida from Virginia. Excellent road manners with no issues what so ever.


37x12.50x18 Toyo ATIII and Icon Compression Titanium 18x9
RTR Spare Tire Mount - VERY Stout compared to Stock.

RTR Grill
Baja Designs LP6s and Corner Pocket Fog Lights

Minimal Tire outside of Sasquatch Fender flares - +25 wheels with 3/4" Spacer = +6 Overall

I already have a Hard Top in my shop now. I will have the Hard Top and Fender Flares painted Eruption Green and then install the JCR Roof Rack. Almost done, I think?

What did you mount the LP6 lights on? Swarfworks?

 

[rguest3]

What did you mount the LP6 lights on? Swarfworks?

Rudy's Offroad Light mount for the Modular Front bumper. This mount has provisions for 2 lights, with the Swarfworks mount you can install up to 3 Lights. The Swarfworks mount may not have been available last year when I searched?

 

[NVCowboy]

I finally took some pictures after installing the New Icon Suspension and Tires and Wheels. I love the way this Bronco drives! I just drove it back to Florida from Virginia. Excellent road manners with no issues what so ever.


37x12.50x18 Toyo ATIII and Icon Compression Titanium 18x9
RTR Spare Tire Mount - VERY Stout compared to Stock.

I love the RTR Tire carrier and hinges, except it doesn’t seem to be that much less expensive than buying a new bumper with swing away carrier.

RTR Grill
Baja Designs LP6s and Corner Pocket Fog Lights

Minimal Tire outside of Sasquatch Fender flares - +25 wheels with 3/4" Spacer = +6 Overall

I already have a Hard Top in my shop now. I will have the Hard Top and Fender Flares painted Eruption Green and then install the JCR Roof Rack. Almost done, I think?

 

[JonDW29]

Rudy's Offroad Light mount for the Modular Front bumper. This mount has provisions for 2 lights, with the Swarfworks mount you can install up to 3 Lights. The Swarfworks mount may not have been available last year when I searched?

Looks great. I really like the look of the round lights inside the bar. I'm thinking JCR pre-runner, then some lights like this. Did you have to pull the bumper to install?

 

[rguest3]

Looks great. I really like the look of the round lights inside the bar. I'm thinking JCR pre-runner, then some lights like this. Did you have to pull the bumper to install?

To install the Light Bracket you will need to remove the Push Bar and the Grill. Not a big deal at all.

If adding the JCR Pre-Runner to the Factory steel bumper, just remove the Grill. Install Light Bracket, Re-Install the Grill then install the Pre-Runner Bar.

With the Rudy's Bracket you can see the inside of the Lights in the Grill Camera. The Swarfworks Bracket with 3 Lights may block the Camera completely depending on how large your lights are?

 

[JonDW29]

To install the Light Bracket you will need to remove the Push Bar and the Grill. Not a big deal at all.

If adding the JCR Pre-Runner to the Factory steel bumper, just remove the Grill. Install Light Bracket, Re-Install the Grill then install the Pre-Runner Bar.

With the Rudy's Bracket you can see the inside of the Lights in the Grill Camera. The Swarfworks Bracket with 3 Lights may block the Camera completely depending on how large your lights are?

Thanks! I'll take that into account. I'm still torn between two or three lights, but I really like the look. I'm not too worried about the camera. As long as I can see I'm not going to run into something, I'm good.

 

[rguest3]

I removed the Soft Top today, which is a lot heavier than I expected.

I will put the Hard Top on later, but I just installed the front sections for shade over the front seats. Looks kinda funky, but the two panels are on there pretty solid.

I also had a little fun with Warn Wheel Center Caps installed on the Front Icon wheels. The caps needed just a little work to sit flat, painted the outside rings black to show off the center Hub and mounted easily.

 

[rguest3]

Here is the latest as of today. Hard Top is on and JCR Roof Rack is next.

I should have the Painted Fender Flares on by the end of the week.

These are great riding trucks. Many, many smiles per mile!

 

[rguest3]

I got the Sasquatch Fender Flares painted and installed today.

 

[Inlinejohn]

I got the Sasquatch Fender Flares painted and installed today.

Nice build. Love what you’ve done. Final wheel offset is +6? Where did you buy FORD hardtop and how much? Still happy with Stage 8. Did you consider Stage 7?

 

[smoot618]

Sorry if this was answered before but did you install the stage 8 kit, or did you have a shop install it?

 

[rguest3]

Nice build. Love what you’ve done. Final wheel offset is +6? Where did you buy FORD hardtop and how much? Still happy with Stage 8. Did you consider Stage 7?

Final wheel Offset is +6 - +25 wheel and 3/4" Spacer (-19).

I purchased the Brand New Hard Top from a member here who lives in Tampa. - $4000

VERY happy with the Icon Stage 8. A lifted Bronco with 37s is NOT supposed to handle like it does. Absolutely Fantastic! The Stage 7 does not have the computer controlled dampening.

 

[rguest3]

Sorry if this was answered before but did you install the stage 8 kit, or did you have a shop install it?

I had Chaos Offroad in Winchester VA install the Icon Stage 8 Suspension.

Sponsored