OP
OP
- Thread starter
- #31
Camera view, not bad, seen worse....Thanks... I'll take a picture n send tomorrow.
Interesting thing... the park assist (overhead view) shows new bumper.
Sponsored
Sponsored
- Joined
- Feb 21, 2022
- Threads
- 25
- Messages
- 98
- Reaction score
- 96
- Location
- Los Angeles
- Vehicle(s)
- 2022 BD Sasquatch 4door
- Your Bronco Model
- Badlands
Nice I have this bumper and side steps ready to install but check engine light came on at 27 miles 
. Hey what’s your tire size 33” or 35”? Looks awesome 
and where’d you get your lightbar?
. Hey what’s your tire size 33” or 35”? Looks awesome and where’d you get your lightbar?
OP
OP
- Thread starter
- #33
Nice and hopefully the engine light is a simple fix...Nice I have this bumper and side steps ready to install but check engine light came on at 27 miles
Tires - 37" K02s, no lift, no levelers.
Light bar - 40" curved from Rigid. The one on the brush bar is a 20" from Nilight on Amazon.
I can do links if needed later.
- Joined
- Feb 21, 2022
- Threads
- 25
- Messages
- 98
- Reaction score
- 96
- Location
- Los Angeles
- Vehicle(s)
- 2022 BD Sasquatch 4door
- Your Bronco Model
- Badlands
Awesome bro looks killer
- First Name
- Tommy
- Joined
- Jun 22, 2020
- Threads
- 4
- Messages
- 579
- Reaction score
- 998
- Location
- New jersey
- Vehicle(s)
- Jeep cherokee
- Your Bronco Model
- Badlands
Awesome job dude!
Sponsored
How heavy was the bumper? Really looking hard at this one!
- First Name
- Corbin
- Joined
- Dec 9, 2021
- Threads
- 1
- Messages
- 18
- Reaction score
- 23
- Location
- Los Angeles
- Vehicle(s)
- Jeep compass
- Your Bronco Model
- Wildtrak
How did you fasten the wire mesh? It looks great! Did you tack weld it in place or are there holes for fasteners. Nice work!Here's what I did today....
Havoc - Nice quality and powder coating was good. Simple install, directions are clear.
Installed a 20" light bar, running the wires into and through the brush bar. The brush bar has a plugged vent hole at each end. I drilled up through the bumper into the brush bar to route the wires. Also, In front of the cooler I installed a wire mesh grill and sprayed the inside of the bumper with bedliner bcuz that's how I roll.
.
OP
OP
- Thread starter
- #39
Hey, there's a bracket that closes off the area from the bumper to the lower grill. The bolts that hold the bracket are securing the mesh.
Do you know if it would hold a winch? Website shows the angular bar style with a winch so I don't see what the round bar would not work?Here's what I did today....
Havoc - Nice quality and powder coating was good. Simple install, directions are clear.
Installed a 20" light bar, running the wires into and through the brush bar. The brush bar has a plugged vent hole at each end. I drilled up through the bumper into the brush bar to route the wires. Also, In front of the cooler I installed a wire mesh grill and sprayed the inside of the bumper with bedliner bcuz that's how I roll.
.
Sponsored
OP
OP
- Thread starter
- #41
It does not support a winch. The does seem to be room for a custom built mount.
- First Name
- Kevin
- Joined
- Jul 16, 2020
- Threads
- 0
- Messages
- 166
- Reaction score
- 311
- Location
- Grand Rapids
- Vehicle(s)
- 2019 Subaru WRX sti, 2019 Ford Mustang GT
- Your Bronco Model
- Badlands
There is a version of this one that is set up for a winch.
https://www.cjponyparts.com/havoc-offroad-front-bumper-steel-bender-winch-ready-bronco/p/HFB02003/
- First Name
- Steve
- Joined
- Oct 6, 2022
- Threads
- 3
- Messages
- 30
- Reaction score
- 45
- Location
- Austin, TX
- Vehicle(s)
- 2022 Wildtrak 4d Hardtop
- Your Bronco Model
- Wildtrak
Does this block the factory tow loops on the front of the Bronco? I can't see them in the pics you posted, but that could just be because everything on the underside is black.
OP
OP
- Thread starter
- #44
N
Hey, not at all. Installed the factory skid plates, left the tow hooks in place with the rubber trim that fits over them. I can send a pic later if you like.
- First Name
- Steve
- Joined
- Oct 6, 2022
- Threads
- 3
- Messages
- 30
- Reaction score
- 45
- Location
- Austin, TX
- Vehicle(s)
- 2022 Wildtrak 4d Hardtop
- Your Bronco Model
- Wildtrak
Thanks for responding. No need for the pictures. I ordered the front and rear bumpers this morning. Can't wait to put them on. Really appreciate your detailed writeup. Don't really feel like I need a winch and did not want to block any of the luxe sensors so this bumper was exactly what I needed.
Sponsored
