OP
OP
- First Name
- Brian
- Joined
- Sep 22, 2021
- Threads
- 49
- Messages
- 894
- Reaction score
- 3,503
- Location
- Portage, Mi
- Vehicle(s)
- 2021 Ford Bronco Badlands
- Your Bronco Model
- Badlands
- Thread starter
- #31
We do not.
Sponsored
Sponsored
JcrOffroad’s new Crusader front and rear bumper!
- Thread starter JcrOffroad
- Start date
- Watchers 8
Got shipping notice today for the rear bumper -- 39 days from order (for those who are curious about current lead times.) I'm hoping to get both bumpers and skid plate installed this weekend. I'm really looking forward to it!
Got the front bumper and engine skid on. We've removed the factory rear bumper and are now at a standstill. There are no included instructions, nor any online videos we can find to install this thing. I'm not looking forward to putting the stock bumper back on so I can drive it home. Hope we can figure this out quickly.
Sponsored
OP
OP
- First Name
- Brian
- Joined
- Sep 22, 2021
- Threads
- 49
- Messages
- 894
- Reaction score
- 3,503
- Location
- Portage, Mi
- Vehicle(s)
- 2021 Ford Bronco Badlands
- Your Bronco Model
- Badlands
- Thread starter
- #36
Look on vanguard rear bumper product page. You can watch that video. Install is the same minus any carrier installations.
Thank for the reply. Our first problem was that we needed to remove the stamped steel factory pieces that are outboard of the frame. Once we figured out, we checked out the same video you referenced, but the brackets install slightly different on the Crusader. It didn't help that we had each on the wrong side. Lol! Now I've found that the four sensor plugs that shipped with the bumper are too big to fit through the holes in the bumper. We're making a little progress though. Lol!
Whoaa, those are sweet!!!
Only set I've liked more than the MOD bumpers so far.
The foot holes on the rear bumper .... Outstanding!!
Great attention to details!
Only set I've liked more than the MOD bumpers so far.
The foot holes on the rear bumper .... Outstanding!!
Great attention to details!
Got most of my project done today (bumpers. engine skid, and steps). I still need to get the lighting wired up, and I ran into trouble with the license plate relocation bracket -- the mount when installed was just too big to install the spare tire on it. When we put the spare onto the bracket and pressed down as far as we could, it still wouldn't clear the camera on the bottom. Close, but no cigar.
All in all, I'm very pleased with the bumpers and engine skid!
This would be the best looking bumper on the market if you could get it without the LED lightbar cutout, and sensor holes cut into it (then plugged). The sad thing is just about no one offers a bumper without the lightbar cut-outs, outside of the Baja bars, or winch bumpers. While all the sensor hole plugs make it less desirable the light bar cutout is the dealbreaker.New Jcroffroad bumper options; Crusader.
Front non-winch bumper. 20” LED bar cut out, works with ACC without relocation. Available with or without prerunner tubing.
Sponsored
I’m not a fan of light bars (for what I need), so I’m kind of with you. However I think a “blacked out” light bar could make it more subtle. Like this one from RC.
https://www.roughcountry.com/20-inch-led-light-bar-70720bl.html
The Crusader Rear is one of my fav so far and might be a great match with my front ARB Summit bumper. Also goes well with the JCR tailgate reinforcement plate
- First Name
- Ben
- Joined
- Jul 25, 2020
- Threads
- 17
- Messages
- 1,753
- Reaction score
- 2,480
- Location
- Interior of BC
- Vehicle(s)
- 2010 Kia Borrego, 2012 Chevy Cruze, 2022 Bronco
- Your Bronco Model
- Big Bend
Do you have more photos of that Summit from the sides and angles? That thing looks nice!The Crusader Rear is one of my fav so far and might be a great match with my front ARB Summit bumper. Also goes well with the JCR tailgate reinforcement plate
Please peruse this link so we don’t hijack JCR’s thread:
https://www.bronco6g.com/forum/threads/bumpers-aftermarket-bumper-list.32655/
I am in the middle of install and have no idea how to mount this Onx6 20 inch light bar. This is confusing as hell.
*edit* I think this bracket won't work with this light which makes all of this a lot less fun.
ANYONE have any tips?
*edit* I think this bracket won't work with this light which makes all of this a lot less fun.
ANYONE have any tips?
Sponsored
Last edited:
