Offset needed for a little “poke” on SAS?

[Tricky Dick]

do you know why so many wheels you come across is -12?

-12 is an offset for Toyota truck wheel so it will not be hub-centric for the bronco.

No problemo.

Sponsored

 

[Raptor911]

does anyone use hubcentric rings any more? Didn't this die with body lifts?

No problemo.

 

[Tricky Dick]

does anyone use hubcentric rings any more? Didn't this die with body lifts?

Probably not. I think most people just run oversized hubs and don't worry about it.

 

[Etienne]

I went the +10mm offest on my BL Sasqatch replacing +33mm offset from factory wheels. This is 23mm more negative (moving wheel more away from vehicle) offset was just under an inch.

Pics of my build using a 18x9 wheel with a 325/65/18 (Almost exact same rolling diameter just .02" taller than stock Goodyears 315/70/17). The actual treads that touch the ground just fit inside of fender where the bulge of the rest of the tire pokes slightly.

 

[Rakkasan187]

Method 17x8.5 0 offset on the wife’s FE.

 

[peterh]

curious how the ADV fenders will look with different set ups - is there
1. less coverage than Standard flare,
2. more than Standard but less than SAS
3. equal to SAS
4. more than SAS?
my guess is equal to Standard but I really don't understand this stuff well at all

 

[MillerAndCheeto]

Method 17x8.5 0 offset on the wife’s FE.

In my opinion that's the absolute perfect offset. No more, no less - perfect.

 

[Rakkasan187]

In my opinion that's the absolute perfect offset. No more, no less - perfect.

Thank you. I couldn’t agree more.

 

[BroncoZ13]

New kicks for the Badlands today. Pics after install at Discount Tire in Leander, TX.

tires - Nitto Ridge Grappler 35x12.50R17
Wheels - KMC “Summit” 17x8.5 +18 offset

Slight more offset than factory +30 Sasquatch wheels, but def like the treads on the Nitto. Just a hair of a “poke” outside SAS fender without the concerns for throwing rocks against body.

The factory Goodyears are a little softer ride vs the E rated Nitto, but highway noise I think is identical.

love the blacked out look with the Shadow Black exterior! Thanks for checking out and hope this helps with your wheel selection

 

[WildTrak]

New kicks for the Badlands today. Pics after install at Discount Tire in Leander, TX.

tires - Nitto Ridge Grappler 35x12.50R17
Wheels - KMC “Summit” 17x8.5 +18 offset

Slight more offset than factory +30 Sasquatch wheels, but def like the treads on the Nitto. Just a hair of a “poke” outside SAS fender without the concerns for throwing rocks against body.

The factory Goodyears are a little softer ride vs the E rated Nitto, but highway noise I think is identical.

love the blacked out look with the Shadow Black exterior! Thanks for checking out and hope this helps with your wheel selection

My current favorite wheel. Waiting for my shadow black to be built. Did you find the KMC's in all black including the beadlock bolts or did you paint/replace them?

 

[Kmcran]

between +35 and +25. I am running +35 and my tires sit flush with base fender flares

I believe sasquatch wheels are already +35 offset.

 

[BroncoZ13]

Hey WildTrak, mine are the Satin Black with Grey Tint selection and the Grey is a dark charcoal which is also the bolt colors. In the pics is how they look in person which almost appear all black unless you get close up to the wheel, so I did not paint/replace.

when ordered I thought the Grey would be lighter to match the grill of my Badlands, but very happy with how dark they look if you are going for an all blacked out look, thanks and hope that helps when you are deciding.

 

[BroncoZ13]

The Sasquatch factory wheels (or at least the ones that came on my Badlands) were +30

that’s why I went +18 to push them out just a tiny bit, but even a 0 work and look nice. Once you start going negative offset is where guys have reported rubbing issues with 35s and more debris thrown since fenders don’t cover.

 

[Jason F]

I’ve been trying to determine what offset I need to get on a new set of wheels to ensure a little poke with the SAS fenders. I do plan on getting slight lift (additional 1-2”) Anyone have any pics of a SAS Bronco with zero offset?

I saw an IG post from Maxslider that had -12 offset and it looked pretty good but it was from an angle so hard to tell if it was too much.

Beware rocks and mud will get kicked up especially from your front wheels. Lots of people reporting this on stock Sasquatch.

 

[Kekov721]

0 offset from the concept l

0 offset from the concept last year.

wow. 0 is perfect! Really makes me happy about the wheels im getting!

Sponsored