PVO update on the attic tray

[Forditude]

Really like this design. Both the shelf and the board mounts. I would be very interested in a combo set. Thanks for offering these to the community.
Right now I have have Monkey Fist mounts bolted to the nut certs...

Sponsored

 

[da_jokker]

I'm going to be installing something similar to this as well but using the XG Cargo bags (once they create them for bronco) for the sides and then a panel ran across the top between the two for attic storage.

I guess my point is if you turn those sides into some storage, you may tap into a market that is not developed for the Bronco yet.

Imagine these, with a Molly panel running across the top of them...

XG Cargo Wrangler Gama Adventure JL https://a.co/d/8XjGG8S

 

[Thart89]

I'm in for a pre-order bundle If you decide to open pre-orders.

 

[huskerhiker]

I'm in too on the attic, assuming my Bronco is made one of these days.

 

[UtahBrandon]

Maybe I missed it but is there a picture with the top on, out of the back window with the tray and the boards mounted underneath. Trying to get an idea how much of the rear window is obstructed. Thanks!

I just realized I didn't post a pic for you. here you go. The attic tray is mounted on top of the Traction Board Brackets but is obscured by the roll bar. The ARB Tred GT boards are mounted underneath the attic tray and Traction Board Bracket

 

[Thart89]

I just realized I didn't post a pic for you. here you go. The attic tray is mounted on top of the Traction Board Brackets but is obscured by the roll bar. The ARB Tred GT boards are mounted underneath the attic tray and Traction Board Bracket

Thanks for the picture. That's not nearly as bad as I was expecting or even as bad as I'm used to. I'm definitely in for both whenever they are ready. Thanks again!

 

[MrGreen55]

I'm going to be installing something similar to this as well but using the XG Cargo bags (once they create them for bronco) for the sides and then a panel ran across the top between the two for attic storage.

I guess my point is if you turn those sides into some storage, you may tap into a market that is not developed for the Bronco yet.

Imagine these, with a Molly panel running across the top of them...

XG Cargo Wrangler Gama Adventure JL https://a.co/d/8XjGG8S

The pre order it up on this for the bronco. In theory looks like you can use both long as the bolt is long enough.
https://xgcargo.com/products/bronco-stealth-gama

 

[vzqhsg]

TL;DR is that the attic trays are being cut and bent right now and they should be ready to be picked up this week. I’ll then take them to powder coat which should take another 10 days or so.

In the meantime, I did a quick video to give you more detail on the tray.

Build a hinge on the front facing side of the rack. You can then drop it down to load and unload. Put a lip on the back facing side so stuff doesn't fall out. Can you get them in colors to match your Bronco.? Also would work for....cover your ears...a JEEP.

Nice looking. I only get 3% development fee, or a free rack. :0)

 

[UtahBrandon]

Build a hinge on the front facing side of the rack. You can then drop it down to load and unload. Put a lip on the back facing side so stuff doesn't fall out. Can you get them in colors to match your Bronco.? Also would work for....cover your ears...a JEEP.

Nice looking. I only get 3% development fee, or a free rack. :0)

I mean, I like it but have resisted complexity like that as It will add to cost, add potential locations for rust, and will potentially rattle. It works great as is.

 

[Gabby]

The traction board bracket won’t fit a two door because the angle of the roll bar is different and it doesn’t have the same available nutserts to mount the bracket.
No idea on load capacity but they’re very durable 12ga steel.
I could probably hold one back from powder if you order early. I’ll dm you when I get it posted on the site.

2dr fitment was going to be my question... If you ever figure a way then I'd be interested.

 

[BlueBoy]

I just realized I didn't post a pic for you. here you go. The attic tray is mounted on top of the Traction Board Brackets but is obscured by the roll bar. The ARB Tred GT boards are mounted underneath the attic tray and Traction Board Bracket

Those Attic Trays look ready to ship??

 

[UtahBrandon]

Those Attic Trays look ready to ship??

I'm dropping them off at powder coaters today (currently raw 12ga steel). They'll take 7-10 days, then they're ready to ship.

 

[2ndGenBroncoOwner]

I'm dropping them off at powder coaters today (currently raw 12ga steel). They'll take 7-10 days, then they're ready to ship.

any bundle pricing or Member discounts?

 

[BostonSasquatch]

Maybe I missed it but is there a picture with the top on, out of the back window with the tray and the boards mounted underneath. Trying to get an idea how much of the rear window is obstructed. Thanks!

Old Class-A trucker here: rear view mirrors are for mallcrawlers!

[Edit: the subsequent image you posted clears up that issue. And yes, I do check my rearview mirror...occasionally...]

A suggestion for the OP: the side moll support triangles open up possibilities for accessories. As you get your operation up and running, consider a quick-release mount for a fire extinguisher.

The shelf looks ideal for my compressor hoses. Everytime I think my Bronco is "finished," somebody like you comes up with something like this. Good thing my wife doesn't look at the credit card statements very often!

I'll probably put in an order in January. Way to go, Brandon!

 

[Mc1guil]

any bundle pricing or Member discounts?

I’d be interested in a bundle as well

Sponsored