Rockworkx hard top bolts installed. Removable by hand

[Chippewa-Pin]

What is the expected time to ship the "Ford Bronco Hard Top FORWARD Quick Removal T40 Torx Thumb Screw 2 pc Set" (green color if that matters) ?

I ordered 5 sets last Saturday and haven't received a shipping notice yet.

Sponsored

 

[We_Love_Tacos]

What is the expected time to ship the "Ford Bronco Hard Top FORWARD Quick Removal T40 Torx Thumb Screw 2 pc Set" (green color if that matters) ?

I ordered 5 sets last Saturday and haven't received a shipping notice yet.

The very first paragraph of the listing: “PRE ORDER- Estimated in stock end of August 2022”.

 

[Chippewa-Pin]

The very first paragraph of the listing: “PRE ORDER- Estimated in stock end of August 2022”.

Thank you.

 

[Rockworkx]

What is the expected time to ship the "Ford Bronco Hard Top FORWARD Quick Removal T40 Torx Thumb Screw 2 pc Set" (green color if that matters) ?

I ordered 5 sets last Saturday and haven't received a shipping notice yet.

We are a little behind, but wrapping up assembly and packaging in the next week, I expect them to be here and to start shipping all the Torx orders the week of the 12 Sept. This was the first run of these so it took a little longer than usual. Cheers, Grant

 

[Rockworkx]

Can you post a pic of the gaskets? I bought 6 but didn't install on the fwd bolt holes because of the lip. Wondering what the gaskets will do

Sorry, I missed your post. The thicker washers are only needed on some hardtop, ones with a raised edge at the forward most bolt holes. Here are some pic's. The 4 mm washer helps the bolt clear the "Lip". You would remove the 1.5 mm washer and replace it with the 4mm. -G

 

[Rockworkx]

Is this for a two door or a four door? I didn't see any 'rib' when I installed on my 4dr, but now I feel the need to go check.

This is what you are looking for. We are still trying to establish exactly which models are affected.

 

[Lifeliberty]

Sorry, I missed your post. The thicker washers are only needed on some hardtop, ones with a raised edge at the forward most bolt holes. Here are some pic's. The 4 mm washer helps the bolt clear the "Lip". You would remove the 1.5 mm washer and replace it with the 4mm. -G

I have that lip. For now i just inserted a couple fender washers to raise it up. Doesn't look great, but works.

Maybe when you ship orders 1333 and 1483 you can send a couple along

ORDER #1333 And Order #1483​

 

[Chippewa-Pin]

We are a little behind, but wrapping up assembly and packaging in the next week, I expect them to be here and to start shipping all the Torx orders the week of the 12 Sept. This was the first run of these so it took a little longer than usual. Cheers, Grant

Thank you for the update!

 

[History]

Could we get some in the code orange color, in anticipation of Raptor deliveries?

 

[MikeOU]

We are a little behind, but wrapping up assembly and packaging in the next week, I expect them to be here and to start shipping all the Torx orders the week of the 12 Sept. This was the first run of these so it took a little longer than usual. Cheers, Grant

Ugh. Shipping same day I go on a 2 week road trip. Can I email someone and update shipping address for my order?

 

[Rockworkx]

I have that lip. For now i just inserted a couple fender washers to raise it up. Doesn't look great, but works.

Maybe when you ship orders 1333 and 1483 you can send a couple along

ORDER #1333 And Order #1483​

Will do, I've added a note to your order.

 

[Rockworkx]

Ugh. Shipping same day I go on a 2 week road trip. Can I email someone and update shipping address for my order?

Sure thing, send a note to [email protected], we can also delay shipping if needed. -Grant

 

[Rockworkx]

Could we get some in the code orange color, in anticipation of Raptor deliveries?

It may be a hard color to hit in anodizing but we can give it a try. U have one on the way?

 

[History]

It may be a hard color to hit in anodizing but we can give it a try. U have one on the way?

Yes!

 

[Herbie]

Shoutout to Grant @Rockworkx for working on the weekend to get these forward bolts shipped out that he just received yesterday. Between him and Curtis @EIGHTLUG working today to get the Badlands BYOD rails out the door, we appreciate you spending your weekends working for your OCD customers.

Sponsored