I need my rack to carry my surf rods, but I love my Sunrider top more. So being bored today, I took out the jigsaw and drill and went to work. Now I have the best of both worlds.
I searched and still can't find an answer. I put new wheels and tires on. Ford mounted the tires and installed the sensors. I drove for a while and all the sensors were transmitting. I went out today and after about a half hour, I got TPMS fault from all 4 wheels. I already have a reset tool...
OK, installed Key 200.4, did the DSP, big improvement. Went to set the gain with the Kicker gain MP3 and can't raise the gain at all without clipping. According to Kicker's website, I'm supposed to set the HU vol to 3/4 which is about 22 on the HU. Anyone else experience this? I'm using the -5dB...
Installed the amp today with direct to battery power. The hardest part was getting the wires routed so I could button up the dash. Sound is a great improvement. JBL's up front, stock kick panels, and SSV pods with MTX Thunders in rear. Left the gain set all the way down. Install went great until...
Upgraded all my speakers except kick panels. Put 6.5" pods in the rear. What settings are best on the key so that i can get full power to the rear and still be able to fade front to rear. My rears sound like crap.
If I bi amp do I lose fade control? If I don't bi amp do I get full power to the...
Hey Mike
My Pet Divider arrived and I had a successful install in my 2 dr. You just need to make a few hardware pieces and you'll be good to go. Let me know what you think. My rear seat bottoms are removed, but should still work with them in.
Anyone know the bolt specs for the small black bolts in the airbag trim on the roll bar? Where you would attach paracord grab handles. Have to drill and tap 2 new holes.
There's an older thread on this, but for those of you putting a Sunrider on your 2dr, don't use the 5.5mm spacer that Bestop supplies. It leaves a large gap on the sides where the Sunrider meets the factory top. Some guys remove the spacer completely, but I found that to put a lot of stress on...
Why is it when you drop a bolt it always falls into that one place where you can't recover it?
Install ing A Pillar lights and I place one of the black accessory bolts on the cowling. It rolls off and drops through a hole and goes under the cowling. I remove the wiper and lift up the cowling, go...
What's with the brakes on my 2.7 Badlands Squatch. Compared to my 23 F150, they're very sensitive, almost too sensitive. It takes a while to get used to it when I go from the truck to the Bronco. Normal?
Installed black lug nuts today. McGard OEM Bulge nuts. F'n Ford couldn't paint the whole wheel black. Had to leave an unfinished ring around the hole.
Next time I take the wheels off, I guess I'll black out the friggin silver.
OK, I looked all over and there is no listing for the tow capacity for a 2DR, 2.7L, 3:73, 10spd Badlands Squatch.
I'm assuming it's 3450 like the Outerbanks etc. Ford just doesn't list the Badlands with the 3:73 10spd.
It shows the manual rating, but the auto is blank.
Anyone other than me get this rack for their 2dr? Having a hell of a time trying to mount this getting it to sit right and not look like it's gonna separate the top from the sides. I used to be a mechanic, so I know what I'm doing, but maybe I'm missing something. Reached out to JCR, but they...
Waiting on a shortie rack from JCR. Selling my OEM 2 door roof rack. All hardware included. Bronco has 800 miles on it.
$400. Pickup only. Highlands, NJ
I'm installing 2 Rigid floods under my rear bumper for camping, fishing, etc. Having problem routing wires to front of Bronco. Anyone route wires to the engine bay from the rear? Thought of using the rear upfitter wire, but want to save that.
OK, so I go to install a safari bar in my Mod bumper and even use my torque wrench to specs. One of the friggin nutserts stripped. Anyone else have this happen?