Squared fender flare options for Bronco?

[CoolContractor]

I haven't taken the rear flares off yet so no pic, sorry, but it's going to look pretty much the same.

Are the rear doors the same as the Badlands or are they squared off as well?

Sponsored

 

[Lowcountry Bronco]

Are the rear doors the same as the Badlands or are they squared off as well?

I'm a 2 door not 4 but all the Heritage's and Everglades fender flares are squared off, front and rear. Something cool the 4 doors don't get is the little slash aft of the rear wheel opening which is a nod to the EBs and is only on the 2 door Heritage's!

 

[gerby151]

Here is a link to the Heritage fender/quarter panels. The front was not as bad as I thought but the rear is pricey.

Fender & Components for 2023 Ford Bronco | Ford OEM Parts Direct

Quarter Panel & Components for 2023 Ford Bronco | Ford OEM Parts Direct

 

[BlueBronco]

Are the rear doors the same as the Badlands or are they squared off as well?

Can confirm that the rear doors are the same. And if you look at an HE the rear flare doesn't flatten out until well past the door. However, if you are thinking that you can interchange the flares, well, I just tried it and can also confirm that will not work.

Also of note, I discovered that the rear quarter trim piece under the brake light (the piece with the little Squatch sticker) is different on the HE's. The forward flat edge that touches the flare is 4" long on an HE and 4.5" long on a BL. This is on a moar door.

 

[CoolContractor]

Can confirm that the rear doors are the same. And if you look at an HE the rear flare doesn't flatten out until well past the door. However, if you are thinking that you can interchange the flares, well, I just tried it and can also confirm that will not work.

Also of note, I discovered that the rear quarter trim piece under the brake light (the piece with the little Squatch sticker) is different on the HE's. The forward flat edge that touches the flare is 4" long on an HE and 4.5" long on a BL. This is on a moar door.

I was just wondering if the 4 Heritage fenders with Heritage plastics would fit the Badlands. Somewhere, someone may have done it already.

 

[BAUS67]

I was just wondering if the 4 Heritage fenders with Heritage plastics would fit the Badlands. Somewhere, someone may have done it already.

Well, the Bronco was designed with a modular platform.

 

[BlueBronco]

I was just wondering if the 4 Heritage fenders with Heritage plastics would fit the Badlands. Somewhere, someone may have done it already.

I am about 98% sure they would be a direct swap. Besides the rear trim piece I mentioned, everything looks identical. Conclusion drawn from comparing them in person side by side.

 

[STX Bronco]

KBDs

This looks great! I wish they were the same width as the Sasquatch flares to keep down the slinging crap everywhere. Your’s is one of my favorites setups.

 

[GI_Jo_Nathan]

I was just wondering if the 4 Heritage fenders with Heritage plastics would fit the Badlands. Somewhere, someone may have done it already.

Its been looked into in other threads. I think the conclusion was that it's too expensive to make sense.

 

[Barny227]

This looks great! I wish they were the same width as the Sasquatch flares to keep down the slinging crap everywhere. Your’s is one of my favorites setups.

Same here, if they were just a little wider.

 

[Chritaka]

I’m also running the KBD’s. Their prep and tape aren’t great, still pull up in spots after taking extreme care for proper cleaning/prep during install. They fade pretty easy, but still shine up decent with some quality dressing. I’ll probably have them painted at some point. Regardless, I love the look and get a lot of compliments.

 

[Chritaka]

I’m also running the KBD’s. Their prep and tape aren’t great, still pull up in spots after taking extreme care for proper cleaning/prep during install. They fade pretty easy, but still shine up decent with some quality dressing. I’ll probably have them painted at some point. Regardless, I love the look and get a lot of compliments.

Note those are 37x12.5 on 17x9 0 offset.

Below are some pics of the poke with the stock WT SAS wheels/tires.

 

[Dangler]

Thank you for this picture. Ford should do this for all Broncos in 2024.

I’m betting on this for 2025

 

[HammerNQuill]

I’m also running the KBD’s. Their prep and tape aren’t great, still pull up in spots after taking extreme care for proper cleaning/prep during install. They fade pretty easy, but still shine up decent with some quality dressing. I’ll probably have them painted at some point. Regardless, I love the look and get a lot of compliments.

I’m also running the KBD’s. Their prep and tape aren’t great, still pull up in spots after taking extreme care for proper cleaning/prep during install. They fade pretty easy, but still shine up decent with some quality dressing. I’ll probably have them painted at some point. Regardless, I love the look and get a lot of compliments.

The square fender and the lower stripe is the look I've been after! Did you trim the stripe, or did you find one pre-cut? Do you have a link?

 

[Strizzo]

Search KBD and Bestop for square flare options. No one's sure yet if you can transfer over the fenders and flares from an HE or EG yet.

They should swap over, but i wouldn't put anything past ford at this point given the number of option and trim-specific parts there already are.

Sponsored