NEW 6 AND 8 CH CLASS D AMPS AT A LOWER PRICE POINT

[plugnplaykits]

WE ARE PROUG RO ANOUNSE A NEW LINE OF 6 AND 8 CHANNEL AMPS PERFECT FOR RUNNING THE ENTIRE SYSTEM IN BASE MODEL OR B & O SYSTEM UP TO 2026 . AMPS WILL COME WITH PLUG & PLAY HARNESS . WE HAVE ADDED THEM TO THE BASE MODEL LISTING AND WILL BE ADDED TO ALL LISTINGS . IF YOU ARE INTERESTED OR HAVE ANY QUESTIONS EMAIL OR CONTACT ME .

KIT 27 RECOIL M1200.6 CLASS D 6 CHANNEL AMP 110W RMS X 6 WITH PLUG & PLAY HARNESS $ 600
6-Channel Amplifier Specifications

Specification​	Value​
Protection Circuit	4-Way Protection (Thermal, Over/Under Voltage, Speaker DC)
RMS Power @ 1Ω (14.4V)	N/A
RMS Power @ 2Ω (14.4V)	210W × 6 Channels
RMS Power @ 4Ω (14.4V)	110W × 6 Channels
Bridged RMS Power @ 4Ω (14.4V)	240W × 3 Channels
Bridged RMS Power @ 2Ω (14.4V)	N/A
Operating Voltage	9V – 16V DC
Idle Current (Power On)	1.5A (1500mA)
Frequency Response	20Hz – 40kHz
Signal-to-Noise Ratio (S/N)	89dB
THD+N (@ 1W)	<0.21%
Low-Level Input Sensitivity	N/A
High-Level Input Sensitivity	N/A
Bass Boost	N/A
Subsonic Filter	N/A
High-Pass Filter (HPF)	30Hz – 300Hz
Low-Pass Filter (LPF)	30Hz – 300Hz
Remote Bass Control	N/A
Clip Indicator	1% THD
Recommended Fuse Rating	100A
Dimensions (L × W × H)	8.81" × 7.48" × 1.81" (244 × 190 × 46mm)

KIT 28 RECOIL M 1600.8 EIGHT CHANNEL CLASS D AMP , 120 W RMS X 6 PLUS 320 W FOR SUB WITH PLUG & PLAY HARNESS $ 750



8-Channel Amplifier Specifications

Specification​	Value​
Protection Circuit	4-Way Protection (Thermal, Over/Under Voltage, Speaker DC)
RMS Power @ 1Ω (14.4V)	N/A
RMS Power @ 2Ω (14.4V)	200W × 8 Channels
RMS Power @ 4Ω (14.4V)	120W × 8 Channels
Bridged RMS Power @ 4Ω (14.4V)	320W × 4 Channels
Bridged RMS Power @ 2Ω (14.4V)	N/A
Operating Voltage	9V – 16V DC
Idle Current (Power On)	2.2A (2200mA)
Frequency Response	20Hz – 20kHz
Signal-to-Noise Ratio (S/N)	90dB
THD+N (@ 1W)	<0.1%
Low-Level Input Sensitivity	N/A
High-Level Input Sensitivity	N/A
Bass Boost	N/A
Subsonic Filter	N/A
High-Pass Crossover (HPF)	30Hz – 300Hz
Low-Pass Crossover (LPF)	30Hz – 300Hz
Remote Bass Control	N/A
Clip Indicator Threshold	1% THD
Recommended Fuse Rating	120A
Dimensions (L × W × H)	10.93" × 7.48" × 1.81" (277.5 × 190 × 46mm)

Sponsored

 

[RedBeardoh]

Stop yelling at me

 

[Brian_B]

WE ARE PROUG RO ANOUNSE

I'm interested.

 

[EOD98]

Nice!

 

[Mr Nick]

I'm new to anything more complex than a normal 4 channel amp plus a sub.

Can either of these amps be configured so that two of the channels are either bridged to a SVC sub, or ran as separate channels to a DVC sub?

Meaning...

6 channel amp:
2 channels - kick panels
2 channels - dash corners
2 channels - bridged to a SVC sub or left separate to a DVC sub

8 channel amp:
2 channels - kick panels
2 channels - dash corners
2 channels - rear pods
2 channels - bridged to a SVC sub or left separate to a DVC sub

If used with the B&O system, do they get a "flat" signal and then get tuned with a built in DSP? Or are they simply amplifying the factory B&O signal?

Again, pardon my potentially incorrect terminology.

 

[Brian_B]

channel amp:
2 channels - kick panels
2 channels - dash corners
2 channels - rear pods
2 channels - bridged to a SVC sub or left separate to a DVC sub

This is exactly what i have done

So the answer to your question is Yes

For the B&O system you need an A2B compatible input to get a clean signal

 

[Mr Nick]

This is exactly what i have done

So the answer to your question is Yes

For the B&O system you need an A2B compatible input to get a clean signal

Thanks. But if these amps don't have a DSP then you're stuck with un-tunable flat signal. Yes/no?

 

[Brian_B]

Thanks. But if these amps don't have a DSP then you're stuck with un-tunable flat signal. Yes/no?

These amps - you are correct

 

[plugnplaykits]

For 95% of people unless you’re hard-core into music and willing to spend thousands of dollars and know how to properly tune a DSP amplifier this option satisfies 95% of people I’ve done hundreds of Broncos and no one has complain that they weren’t happy with the upgrade. The BNO system only puts out about 30 W and that is the problem there’s not enough power in the overrated BNO system. If you want a flat signal, then you need an interface at $450 not including the amplifiers to re-power everything for a full flat signal. .This is a cheaper option than the musway amps and still a class D amp with pure power and a fantastic deal at this price point .

 

[plugnplaykits]

I sell amps with DSP up to 16 ch ams and standalone DSP‘s. I have every option available as well as interfaces, . but most people’s budget on Broncos want less expensive options lately . I am a paid sponsor on here if you would like to talk about other products that you offer from other vendors please do not push other products within my post just like I don’t push options on Mobridge or any other vendors on here that offer products.

Sponsored