- Thread starter
- #1
I can't decide what type of lights to put on top of my Velocity Blue Outer Banksquatch. Need to order soon, so I can get all my mods installed that are piling up in my dining room. Show me what you went with!
Sponsored
Sponsored
- First Name
- Joseph
- Joined
- Jul 22, 2020
- Threads
- 7
- Messages
- 133
- Reaction score
- 450
- Location
- Roseville, CA
- Vehicle(s)
- Jeep Wrangler Unlimited Rubicon JK
- Your Bronco Model
- Badlands
KC Gravity Pro 6 - 50 inch light bar.
Same as TraumaJoe,,, 50" KC Gravity Pro6. Just waiting on my Bronco,, any day now.
Hereās a set on my 2 door! Iām in the process of overlaying red on top of the white FE decalsā¦I was Going to put custom decals over the lights, with the kc logo as an outline in red also. But may consider instead putting yellow on the decal pieces now instead lol..canāt decide!
- First Name
- Dylan
- Joined
- Jan 25, 2021
- Threads
- 12
- Messages
- 88
- Reaction score
- 183
- Location
- Philadelphia
- Vehicle(s)
- 2021 Base Bronco
- Your Bronco Model
- Base
50ā pro6 for me too.
Sponsored
- First Name
- Jason
- Joined
- Dec 6, 2021
- Threads
- 6
- Messages
- 59
- Reaction score
- 149
- Location
- Maple Valley
- Vehicle(s)
- 2021 Bronco 2dr Wildtrak
- Your Bronco Model
- Wildtrak
Nice, which mounts are these?
- First Name
- Jason
- Joined
- Dec 6, 2021
- Threads
- 6
- Messages
- 59
- Reaction score
- 149
- Location
- Maple Valley
- Vehicle(s)
- 2021 Bronco 2dr Wildtrak
- Your Bronco Model
- Wildtrak
- First Name
- Joe
- Joined
- Jul 14, 2020
- Threads
- 5
- Messages
- 137
- Reaction score
- 662
- Location
- Adairsville, GA
- Vehicle(s)
- Several Fords
- Your Bronco Model
- Badlands
I should have these installed in the next week or so. I love the old school look. We are going for a RetroMod theme.
Sponsored
Are these lights running off one harness or each are seperate?I should have these installed in the next week or so. I love the old school look. We are going for a RetroMod theme.
- First Name
- Brett
- Joined
- May 11, 2021
- Threads
- 2
- Messages
- 176
- Reaction score
- 386
- Location
- Caddo Mills TX
- Vehicle(s)
- 2020 Explorer, 2005 Ranger FX4, & 2021 Bronco
- Your Bronco Model
- Big Bend
I went with these. Going to put 4 inchers on the front.
- First Name
- John
- Joined
- Feb 6, 2021
- Threads
- 0
- Messages
- 130
- Reaction score
- 241
- Location
- Massachusetts
- Vehicle(s)
- LC100, Gen2 Pilot, MX P100D, Gen1 MDX, 2021 Bronco
- Your Bronco Model
- Badlands
KC 50" Pro 6 - Installed last week. Running with covers is not required in my state, so still deciding whether to use them. Hardest part of install was getting access to the roof wire for the Aux switches without drilling. I routed the wires behind and around the roof seal as shown below (as per Ford technician guide for roof lights). The lights do cause turbulence and the soft top to vibrate at speed as acknowledged by KC, but not too bad.
These are wires before tucking inside the inner seal. They are not currently visible. This method is difficult because of the sticky tar based sealant between the roof and outer seal.
These are wires before tucking inside the inner seal. They are not currently visible. This method is difficult because of the sticky tar based sealant between the roof and outer seal.
Last edited:
Are there any needed brackets for the KC Gravity Pro 6 - 50 inch light bar to attach to the Bronco?
Sponsored
