Vinyl / PPF Request

[CKXVII]

@StickerFab @Underground Graphics @Ridergraphix @vortexSigns

Can we get some vinyl graphics for the windshield frame, roll bars & rear cross bar?

Can we also get some PPF strips for the cargo surface that the hard/soft tops sit on? So far, have only seen something like this from Bestop, but it was part of their fastback soft top.

Sponsored

 

[Underground Graphics]

@StickerFab @Underground Graphics @Ridergraphix @vortexSigns

Can we get some vinyl graphics for the windshield frame, roll bars & rear cross bar?

Can we also get some PPF strips for the cargo surface that the hard/soft tops sit on? So far, have only seen something like this from Bestop, but it was part of their fastback soft top.

We've just finished our bedside top, or better termed Cargo area tops. Here's an example below. We did a prototype on ours and made an install video, just have a minor tweak or two and it will go live on our site soon.

As for the windshield frame, ...can do.

However, other than the roll bar protection from the soft top mechanism, we have no plans for a full roll bar kit at this time.

Greg

 

[cmcbronco]

@StickerFab @Underground Graphics @Ridergraphix @vortexSigns

Can we get some vinyl graphics for the windshield frame, roll bars & rear cross bar?

Can we also get some PPF strips for the cargo surface that the hard/soft tops sit on? So far, have only seen something like this from Bestop, but it was part of their fastback soft top.

I’ve reached out to a couple ppf places. So far all have refused to do my roll bars. Must be difficult. I wanted to have them satin black like the 2 door cyber orange reveal bronco. Hopefully I’ll find someone to do them.

 

[CKXVII]

I’ve reached out to a couple ppf places. So far all have refused to do my roll bars. Must be difficult. I wanted to have them satin black like the 2 door cyber orange reveal bronco. Hopefully I’ll find someone to do them.

PPF is likely too stiff to wrap around the roll bars…vinyl wrap may be the way to go?

 

[cmcbronco]

PPF is likely too stiff to wrap around the roll bars…vinyl wrap may be the way to go?

I guess I didn’t think about the differences good point. I’d like something though because I think the satin black looks bad ass. And some added protection for the roll bars would be nice. I’ve noticed after lifting my top off for the first few times with my lift it’s damn close to the rear bars. Don’t want them scuffed up taking the top off and on.

 

[Underground Graphics]

If you're wanting to wrap the roll bars, i'd suggest jut going to a local wrap shop. This kind of job as a pre-cut kit is near impossible to do correctly. Cost wise and time wise.

 

[cmcbronco]

If you're wanting to wrap the roll bars, i'd suggest jut going to a local wrap shop. This kind of job as a pre-cut kit is near impossible to do correctly. Cost wise and time wise.

Appreciate the response. Like I mentioned I reached out to a couple wrap places and so far it’s a no go.

 

[Underground Graphics]

@StickerFab @Underground Graphics @Ridergraphix @vortexSigns

Can we get some vinyl graphics for the windshield frame, roll bars & rear cross bar?

Can we also get some PPF strips for the cargo surface that the hard/soft tops sit on? So far, have only seen something like this from Bestop, but it was part of their fastback soft top.

Kits are ready!!

PPF Cargo area tops(link)

 

[cmcbronco]

Kits are ready!!

PPF Cargo area tops(link)

A.) No two door . B.) is there a color choice?

 

[Underground Graphics]

A.) No two door . B.) is there a color choice?

One we get a two door in the shop, we'll get a template made.

No color because PPF is clear.

Greg

 

[cmcbronco]

One we get a two door in the shop, we'll get a template made.

No color because PPF is clear.

Greg

Thanks Greg. Just thought you’d offer some color choices. I think black would look nice there.

 

[Underground Graphics]

Thanks Greg. Just thought you’d offer some color choices. I think black would look nice there.

We can absolutely do that, LMK if you want to do a color!

 

[cmcbronco]

We can absolutely do that, LMK if you want to do a color!

When you get your two door template done let me know! Would love to have some. Also I guess the more technical term for colored is vinyl haha sorry sometimes i think ppf and vinyl are the same.

 

[Richw23]

@StickerFab @Underground Graphics @Ridergraphix @vortexSigns

Can we get some vinyl graphics for the windshield frame, roll bars & rear cross bar?

Can we also get some PPF strips for the cargo surface that the hard/soft tops sit on? So far, have only seen something like this from Bestop, but it was part of their fastback soft top.

i would love to see that option

Sponsored