What did you do TO / WITH your Bronco today? 👨🏻‍🔧🧰🚿🛠

[rbalazs]

Knocked out a few small projects.
-Installed Bison Gear rear attic shelf

-Installed BD Squadron fog pocket kit from SPV
-Swapped lenses on ditch lights

-Finished installing some more rear cargo lighting with a Kingpin light

I have a couple questions about the kingpin light. Did you run the 28 inch light? Did you tie into 12 V near the dismal rear cargo light? And lastly, did you add a secondary switch or dimmer?

I guess ultimately are you happy with the light?

Sponsored

 

[broadicustomworks]

After an unfortunate and stupid moment last week the surgery has begun.
This one cost dearly.
Both in $$ and in the fact I didn’t get to take it to SuperCel.
By the time I’m done:
Repaint fender
Repair and repaint the bumper.
New grille and lower “chin” both painted
New:
-passenger LCA, both knuckles (went the @BigMeatsBronco route with the RC ones)
-Adjustable UCA
-SD rack #2
-both hub/bearings (OE has a bit of resistance so why not while I’m at this point?)

 

[Rockledge]

Finally got around to installing the Asfir trans skid plate. Transmission crossmember skids (thanks to Broaddict for the idea )and a tailgate table.

 

[cynicalrider]

Got the awning and Maxtrax back on after installing the Top Oak Stellar tent. Saved $300 on the tent by picking it up right at the warehouse.

Untitled by MJH Creations, on Flickr

I originally had the tent more forward but could feel the drag and had some nasty whistling. Trying this setup now with the maxtrax upfront again like I used to have it.

Untitled by MJH Creations, on Flickr

Untitled by MJH Creations, on Flickr

I also needed to hack up my TrailRax 270 awning corner mount quite a bit to get it to fit. Will be hitting up my buddy with a spool gun to beef it back up and adapt it for my use. Only have a mig welder and don't want to get a bottle of Argon for a one off project.

 

[cynicalrider]

Knocked out a few small projects.
-Installed Bison Gear rear attic shelf

-Installed BD Squadron fog pocket kit from SPV
-Swapped lenses on ditch lights

-Finished installing some more rear cargo lighting with a Kingpin light

Is that their new style that is both red and white? Is the switch right on the light too?

 

[Fastmc25]

test fitted my flag pole. Getting ready for Memorial Day and The 250th Anniversary celebration.

 

[Rumbloki]

test fitted my flag pole. Getting ready for Memorial Day and The 250th Anniversary celebration.

Will they hold up at 90mph?

 

[Fastmc25]

Will they hold up at 90mph?

Guaranteed not to explode at high speeds
I don’t drive 90 mph but it has a spring base. It might lay down

 

[ejpaul1]

With deliveries just around the corner, let's kick this off. Anything pretty much goes from major mods, regular maintenance, a good wash and wax or coated it mud off roading.

Seeing who'd win in a game of chicken with a transit, lets just say i won and didnt even wanna play

 

[Mean Green]

That sucks…

 

[JAI STYLES]

It’s been a slushy, snowy mess where I live, up until about yesterday, so for the first time this year I took off the front roof panels for some cruising to and from work.

Only a couple more weeks before it’s time to remove the whole roof and doors for some day trips in the mountains!

 

[BigMeatsBronco]

I replaced the fuel sender in the tank (old one was broken) and then ran new wires to the BCM ( the wires had an intermittentshort since 2022) . Yay, now it works again.!

 

[BigMeatsBronco]

After an unfortunate and stupid moment last week the surgery has begun.
This one cost dearly.
Both in $$ and in the fact I didn’t get to take it to SuperCel.
By the time I’m done:
Repaint fender
Repair and repaint the bumper.
New grille and lower “chin” both painted
New:
-passenger LCA, both knuckles (went the @BigMeatsBronco route with the RC ones)
-Adjustable UCA
-SD rack #2
-both hub/bearings (OE has a bit of resistance so why not while I’m at this point?)

Uh, i only use the rough country knuckles.As a test for a very short time.Maybe like two weeks and then took them off immediately. My current setup uses FMI knuckle/uprights from a 23 F-150 Raptor...NO Comparison with the RC junk! The rough counties are too tall to run without their lower drop brace ...The brace/ Bracket moves the LCA down about 4"... dont go that route unless your ONLY a mall crawler.

 

[SierraBronco]

I ran some new brake lines. Did some cutting.

 

[ItsASamquanch]

Is that their new style that is both red and white? Is the switch right on the light too?

I went with the dual color 12”, pinned it to a Deutsch connector, and tied it to the 12V plug in the cargo area. I haven’t decided if I’m going to make that always hot yet or tie it into a different location.

https://kingpinequipped.com/products/f-series-12-light

Sponsored