Search results

Disregard. I solved the problem and it won't let me delete the post.

I can’t get the weatherstripping above the taillight back on. There is a post that is missing whatever holds it. Is this something available without purchasing the entire assembly?

The warranty on my Bronco runs out in June. (Currently has 12,000 miles on it.) It was leaking oil which turned out to from the back of one of the heads. I'm not sure if they are repairing or replacing the head, either way, it's a fairly major disassembly of the engine. Should I expect them to...

I have recently added a couple of things wired direct to the battery that always draw a small amount of current. Plus my Bronco sits a lot and does mostly short trips. Not surprising that I started getting "system off" messages in Ford Pass. So, it was time to install a battery maintainer. The...

I have a Anker alternator charger to install in the rear of my Bronco. I want to run parallel wires to install a power bus in the cargo area. Where can I find the cable for this? I'm looking for cables already in a loom. Not sure of the wire size yet, thoughts on that? A fuse and Anderson...

I am getting ready to install a two way radio and am concerned how it may affect the Bronco's electronics. I am looking at a 50 watt VHF/UHF setup and want to mount it behind the glove box with the antenna next to the factory radio antenna. Would I be better off mounting the radio to my...

If you have the Motley tool set, they have trays for your tool box now. https://motleyind.com/products/motley-industries-premium-laser-cut-foam-organizer-trays-for-the-122-piece-ford-performance-tool-kit

I saw this in one of the facebook groups. https://thebracketbros.com/

I just noticed two things on the Ford Performance website. The hardware (Procal delivery tool) is now being sold separately from the tune, and the non California tune is "sold out."

I installed Armorlite flooring and need to get rid of my original carpet. 4 door. Pickup only. (North of Dallas.)

I just got notified that parts are in to replace my recalled camera. Assuming they actually replace the camera, how far does the harness go before it plugs in? I'm hoping the connection is at the camera. Otherwise I may have to remove some modifications.

I am installing the stage series pocket fog light setup from Diode Dynamics. I am connecting the fogs to the factory harness and headlight switch via a pigtail. To run the amber backlights, I will need to tap the pigtail into the wiring harness that came with the light set. I have a couple of...

Product Link: https://performanceparts.ford.com/part/M-17757-BMP Install Instructions: https://www.bronco6g.com/forum/attachments/installation-instruction-0amodular-bumper-pdf.749547/?hash=74e4a70736e69552e47e0822e788d782 Part Number: M-17757-BMP Retail: $1,195.00 Upgrade your 2021-2026...

I’ve already been through the firewall twice and I know I’ll do it at least two more times, maybe more. I wish I had known about this part when I installed my mObridge amp. (That was my first pass through.) Now I’ll have to deconstruct a little to get this in, I’m ok with that. Life will be much...

I will be installing a compressor, and am considering adding an air tank as well. That got me thinking about something else I have always wanted. A legit train horn! Who has one, and how did you install it? Got any good stories about how folks react to it?

Noticed oil on the transmission bell housing, the transmission lines and all over the stabilizer bar. There is oil around the engine drain plug, I think that’s where it’s coming from. Minor amount, the dipstick shows full. Wiped it all clean will recheck soon. Drain plug? Is this a common...

I am trying to order a skid plate for my 2023 2.7 Wildtrak, and the dealership is telling me this wont fit, and that the transfer case skid plate for a 2.8 does not exist. I'm trying to verify what I'm ordering will fit. I got the part numbers from this thread. It's an older post...

I am installing Molle panels and will need to trim my rubber cargo mat. I really want the cuts to be clean. I have seen some pictures where others have trimmed the corners for access to the tie down rings and the cuts were rough. Maybe a paper cutter? Ideas?

My WolfBox mirror had bad vibration issues. I’m not the only one experiencing this. The solution is to shim between the back of the mirror and the Wolfbox OEM mount. I found a piece of scrap Velcro in my toolbox that was the perfect size and thickness. No more vibration. I really like this...

I discovered this when I was replacing the drivers side panel in the cargo area. I'm assuming it was not connected to anything. What is this for?