OP
OP
- Thread starter
- #61
Looks so good !!Finally got my KC lights on.
Sponsored
Sponsored
Even a noob can wire something - installed 5" inch KC lights
- Thread starter BroncoAdventures
- Start date
- Watchers 13
- Joined
- Sep 23, 2021
- Threads
- 4
- Messages
- 1,318
- Reaction score
- 2,977
- Location
- New Brunswick, Canada
- Vehicle(s)
- 2021 Bronco Badlands (7spd) 2022 Mustang GT PP
- Your Bronco Model
- Badlands
Just a thought for those that are deciding to run without the antenna, may want to look at installing a short bolt or plug or something to stop water pooling inside the recess?
OP
OP
- Thread starter
- #63
good idea !!! I actually found I can fit my kc lights perfect at a angle towards the ditch with my antenna on . It’s really where I wanted them in the first place so lucky me
Did you end up getting the slimlites? I'm thinking of putting a pair on my bumper too. I was just hoping someone beat me to it so I could see how it looks firstI ordered a set of the KC slimlite LED's 6in. Can't decide if I want to do bumper mount or A-pillar. Picture of my old Bronco for reference (had to get some KC's for my new one)
- First Name
- DREW
- Joined
- Jul 16, 2020
- Threads
- 14
- Messages
- 530
- Reaction score
- 1,900
- Location
- ATLANTA GA
- Vehicle(s)
- 2003 Miata....
- Your Bronco Model
- Badlands
I got the slimlites but I mounted them on the A-pillar spots.Did you end up getting the slimlites? I'm thinking of putting a pair on my bumper too. I was just hoping someone beat me to it so I could see how it looks first
Sponsored
Looks good! Do you think there's enough room to mount directly to the bumper or would I need a bump out spacer?I got the slimlites but I mounted them on the A-pillar spots.
- First Name
- DREW
- Joined
- Jul 16, 2020
- Threads
- 14
- Messages
- 530
- Reaction score
- 1,900
- Location
- ATLANTA GA
- Vehicle(s)
- 2003 Miata....
- Your Bronco Model
- Badlands
It would have been a very tight fit up front. I sat one there to test fit and thought I would need some extra pieces so I mounted them up on the A-Pillars.
- First Name
- George
- Joined
- Jan 28, 2021
- Threads
- 17
- Messages
- 76
- Reaction score
- 134
- Location
- Peoria, AZ
- Vehicle(s)
- 2015 F150, 2013 Traverse, 2007 Mustang Conv.
- Your Bronco Model
- Outer Banks
XM antenna is on the roll cage at the rear.
- First Name
- DREW
- Joined
- Jul 16, 2020
- Threads
- 14
- Messages
- 530
- Reaction score
- 1,900
- Location
- ATLANTA GA
- Vehicle(s)
- 2003 Miata....
- Your Bronco Model
- Badlands
Hey what Aux switch did everyone use? I just realized I might have used one with to low amps. 
Sponsored
OP
OP
- Thread starter
- #71
That’s a happy broncoI got the slimlites but I mounted them on the A-pillar spots.
- First Name
- William
- Joined
- Apr 19, 2021
- Threads
- 4
- Messages
- 222
- Reaction score
- 273
- Location
- Long Island, NY
- Vehicle(s)
- Ford Explorer
- Your Bronco Model
- Outer Banks
Right on man! Looking to do same set up, but someone spoke about amp output on AUX 3 being too low?I got the slimlites but I mounted them on the A-pillar spots.
- First Name
- DREW
- Joined
- Jul 16, 2020
- Threads
- 14
- Messages
- 530
- Reaction score
- 1,900
- Location
- ATLANTA GA
- Vehicle(s)
- 2003 Miata....
- Your Bronco Model
- Badlands
Yea I'm going to have to re-wire it this weekend. I read the specifications wrong on the lights. They are 4amp EACH lol. I have it wired to aux 6 currently which is only 5amp. Ill have to move it to at least 3 which is 10amp
- First Name
- DREW
- Joined
- Jul 16, 2020
- Threads
- 14
- Messages
- 530
- Reaction score
- 1,900
- Location
- ATLANTA GA
- Vehicle(s)
- 2003 Miata....
- Your Bronco Model
- Badlands
Well after I saw this I think I'm fine. I wonder which diagram is accurate. I've seen 2 diff now.
Finally got my Bronco in on Thursday, and I've had these KC Hilites (model 651) in the garage waiting to install. What brackets did you guys use/make?
Sponsored
