Show us your installed wheel / tire upgrades here! (Pics)

[WoolyBugger]

Very nice! 285/75R16 Tires?

Sponsored

 

[Shane78]

Wasn't me unfortunately, I was installing my AIG rear lift struts.

The odds were slim but worth asking, they are popping up everywhere now!

 

[est1776]

Looks to be about a 2" poke with standard flares. Sas would be even less of course.

 

[straycat]

The odds were slim but worth asking, they are popping up everywhere now!

I think I've still only seen 2 or 3 in the wild.

 

[Shane78]

I think I've still only seen 2 or 3 in the wild.

I’m right around Ladue/Clayton and they are a daily occurrence here now

 

[straycat]

I’m right around Ladue/Clayton and they are a daily occurrence here now

Yeah, out here in St. Peters its still very much Wrangler country. So many Wranglers.

 

[JayhawkJake]

I'll add glamor shots later when I take them, but figured I'd throw the first impression pics in here anyways.

Alphaequipt Grenade
17 X 8.5
+0 Offset
285-70R17 Falken Wildpeak A/T3 Load Range "C"
Stock height Black Diamond, no Sasquatch

Note: Anyone saying this type of setup fits with no lift & not removing crashbars is lying. It 100% rubs both the front and rear crash bar on flat ground. I removed both. Not trying to single people out, I just feel like I've seen that claimed, unless I misunderstood. Luckily removing the crashbars is relatively easy, so NBD, just know you'll need to.

Here are the poke shots. Stock non-sasquatch fenders. I like it this way, adds a little girth and isn't obscenely far out. Sasquatch flares should cover all of it though, or at least the tread.

 

[Will_05]

I'll add glamor shots later when I take them, but figured I'd throw the first impression pics in here anyways.

Alphaequipt Grenade
17 X 8.5
+0 Offset
285-70R17 Falken Wildpeak A/T3 Load Range "C"
Stock height Black Diamond, no Sasquatch

Note: Anyone saying this type of setup fits with no lift & not removing crashbars is lying. It 100% rubs both the front and rear crash bar on flat ground. I removed both. Not trying to single people out, I just feel like I've seen that claimed, unless I misunderstood. Luckily removing the crashbars is relatively easy, so NBD, just know you'll need to.

Here are the poke shots. Stock non-sasquatch fenders. I like it this way, adds a little girth and isn't obscenely far out. Sasquatch flares should cover all of it though, or at least the tread.

Maybe the tires are rubbing because of the 0 offset?

 

[JayhawkJake]

Maybe the tires are rubbing because of the 0 offset?

Possible, but I swear I've seen people go 0 offset no lift and say no rub. I mostly just wanted to be clear in my post incase someone else comes across it

 

[est1776]

Badass! Any noticeable rub without the lift?

Pre-lift I ended up having to remove both front and rear crash bars. I haven't explored putting them back on post-lift.

3" ICON lift/35" tires/16" wheels 0 offset/2" of poke with standard flares.

 

[JBaker42]

Here you go!

I just ordered the same rims for mine. Did you need to change the lug nut or were you able to use the stock ones?

 

[cksov1]

I just ordered the same rims for mine. Did you need to change the lug nut or were you able to use the stock ones?

I had to get new lug nuts.

 

[MacDonald_Photo]

New shoe day for me.....
KMC Dirty Harry in 17x8.5 & 18mm offset
Stock BL tires on them.

 

[mjrcu]

No r

OBX, 17X9 KMC KM545 Trek with 285/70R-17 KO2's. No lift

no Rubbing or crash bar removal?

Sponsored