which hood prop?

[Valhalla]

Okay, makes sense. As I read this I wondered why. Then I thought about how old hoods did a coil to lift . I assume factories left that for costs and weight savings. Once I guessed that I considered the tensile strength of tho hood they make. I now wonder if the pivot point where a non stock prop attaches on a long enough time line, will start to damage the hood.
Just how my thought process went. I may be off.

Sponsored

 

[Valhalla]

I like the raise the hood higher. One thing I liked about all my HEEPs was the ability to open the hood back to the point it restedon the windshield.

 

[AB8DT]

MRT https://www.shopmrt.com/2021-Bronco-MRT-No-Drill-Hood-Lifts-80K110-p/80k110.htm
Small but powerful. Highly recommend especially if you plan on an onboard compressor in the engine bay you need the smaller size & clearance

.

 

[userdude]

I open and close the hood every morning and evening dealing with a raccoon issue...

Deer camera hooked up to a train horn under the hood. Should fix that raccoon up! lol

 

[retiredarmymp]

That's a reasonable consideration, but so far after a lot of use, I haven't noticed any signs of strain on the attachment points or hood in general.

Related to that though, it seems to me the struts that attach closer to the hood pivot point might cause more stress due to the leverage and greater cylinder force needed, so review that aspect if concerned.

Also I did not remove the stock hood prop. In case of some high wind situation, it might be better to use that. Otherwise the hood struts I got are convenient, more out of the way and raise the hood higher than the stock prop. Struts are not required but I appreciate them every time I have to raise/close the hood.

That’s another aspect of the MRT hood struts that I didn’t mention in my post earlier. That if you’re using MRT hood struts and you have your hood open on a windy day watch how the top of the hood bounces continually up and down and then look at the hood at the fulcrum point where the hinge mounts to the hood and you can see it flexing. Eventually that will likely be a failure point.

 

[Redline Tuning]

https://www.redlinetuning.com/SearchResults.asp?Search=2021++Bronco

Redline Tuning is pleased to be a sponsor on the Bronco6G forum and want to showcase our 100% Bolt-In MADE IN THE USA Hood QuickLIFT system for the Bronco. Our system is the ORIGINAL Bolt-In system for the Bronco and installs in less than 10 minutes with no modification required to your vehicle or for you to un-bolt you hood to mount any brackets. We offer two different lift heights for the Bronco. Our standard QuickLIFT system raises your hood to the same height as the factory Prop Rod and our Max Lift system raises the hood 8 inches higher for maximum access to the engine compartment. Both systems are available in PLUS, Carbon and ELITE versions as shown below.

QuickLIFT PLUS features:
* All black powder-coated mounting hardware
* Black e-coated gas springs
* 4 year warranty
available directly from our website here:
QuickLIFT (same height as stock)
https://www.redlinetuning.com/2021-Ford-Bronco-Hood-QuickLIFT-PLUS-p/21-11040-02.htm
MaxLift (8" higher than stock)
https://www.redlinetuning.com/2021-Ford-Bronco-Hood-QuickLIFT-PLUS-p/21-11039-02.htm

QuickLIFT CARBON features:
* All black powder-coated mounting hardware
* Black e-coated gas springs with real carbon fiber sleeves
* 4 year warranty
available directly from our website here:
To add the Carbon option check the box show below on our website:

QuickLIFT (same height as stock)
https://www.redlinetuning.com/2021-Ford-Bronco-Hood-QuickLIFT-PLUS-p/21-11040-02.htm
MaxLift (8" higher than stock)
https://www.redlinetuning.com/2021-Ford-Bronco-Hood-QuickLIFT-PLUS-p/21-11039-02.htm

QuickLIFT ELITE features:
* All black powder-coated mounting hardware
* 316L Stainless Steel gas springs
* 5 year warranty
available directly from our website here:
QuickLIFT (same height as stock)
https://www.redlinetuning.com/2021-Ford-Bronco-Hood-QuickLIFT-ELITE-p/21-11040-03.htm
MaxLift (8" higher than stock)
https://www.redlinetuning.com/2021-Ford-Bronco-Hood-QuickLIFT-ELITE-p/21-11039-03.htm


Free shipping in the CON. U.S. on all Bronco systems using coupon code "Bronco6G" at checkout.

You can watch the video below to see how easy our installation is, the only tool required is a 13mm socket:



Here is a video of the different gas spring finishes and the system in action:



Redline Tuning has been developing our Hood QuickLIFT systems for over 20 years and have applications for over 350 unique vehicles, check out our website for your vehicle application.

Please contact us for any questions.

Sponsored