After delating rear seats and replacing new audio system in my car it was time for another projects installing some off-road roof lights
Plan was to use 2or 3 round rally type spotlights in the bumper of my bronco but with factory skinny narrow bumper it was impassible to dit the lights i like...
After seeing several videos I have good idea how to or where to connect wire from the roof lights trough the bracket corner of the windshield area to the glove box and kick panel
I was going to use as many mentioned 1 st switch on the control panel since has thicker dia wire , it’s what I...
Well,
it took me good 2 months to upgrade my audio system and ditching Vietnamese paper woofers out of new Bronco. Well worth project !
I started with sound treatment entire car accepts under front seats.
Since I am audiophile and at heme I have build specific listening room I wanted to...
I wanted to cramp my power wires and ground wires and noticed I don’t have hi tech crimping pliers
I figured I try this trick and did perfect job !
used small vise and place 4 G wire with spade and right next to the belly steel ball from compression shock I believe it was right up against and...
I wanted to show what the speaker output looks like on the Bronco base audio
There are two of them on the left ( gray one ) is speaker out and blk one on the right ANC anti noise ? By pass plug
Hope this help anyone looking fit harnesses and more
To dismount the heater/ audio knob console you...
Hello, wanted to pick few brains here in reference to upgrading new audio ( non B&O )
I ran brand new 14/16 G speaker wires to the kick panel and dash will run 3 way audio front stage only with tweeters/ mids in the dash and 6,5” mid bass drivers in kick panels.
Have all wired up and wanted...
I am in process installing my new Hertz Legends 6,5” midbass drivers in kick panels
Problem is that you need new 6,5” rings to fin in exiting fit
Instead fabricating two I just cut the cheap exiting drivers out of original ring and done !
I was able to fit perfectly in same spot I did trimmed...
This was not as difficult and many might think , as long as you have proper tools deleting seats takes about hour of your time.
I am doing this because I will be installing 2 full sliding drawers side by side pause in the rear area , 2 amps audio rack plus single sub enclosure.
this gives me...
Just about all done with dash mods
It was fun project using great Kydex plastics used fir gun holsters , very easy to cut or mold to shape
I actually use it on my kayak kill guard works superb
Here what I did since I will be Triamping 3 Way front stage I needed to make plates to accommodate both...
I was Looking for easy hole to pull the power cable to the battery from the amp and on the driver side Ford made very nice big 1” oval rubberized cup you can remove it slice hole in it and send your audio electric cable
I used good quality 4 G cable
Hello , looking fir the right radio - amp harness fur Bronco non B&O audio.
I will be installing just front stage 3 way audio and trying to figure out what harness to get , or perhaps cut in to wires and make my own .
any help will be greatly appreciated. Please note that I will be using non DSP...
so far so good ! installed cheap Frost King insulation to my ne Bronco , Cargo Floor, side panels and all 4 doors
Here are the sound level test results done befor and after. Hope this help people doing them self , well worth it , this is my second car I have done and have very similar results...
Short video showing why even cheaper stuff works and wort applying inside of your Bronco
I have used the same product in my Xterra and worked perfect , no peals , no odor and dead sound from outside
Did check with sound level checker and dropped fro 60’s dB 2-3 dB 2-3 might not sounds big but...
Since I wanted to set 3 way front stage I started on dash mid/tweeter modification of the plates.
this project requires basic skills of cutting plastic and few handy tools like Power drill , band saw would be handy but not needed.
What I did I left original midrange speaker plate and build 2...
Day 2 working on doors after finishing side cargo and floor cargo area
I used cheaper product I had great results in last build on my Xterra
I will post short video soon plus how to take door panels off
Hello ,
I am in process slowly starting to build new audio in my new 4 door Bronco
I have 2 amps and wanted to fit bot of them in the cargo storage tub. fortunately the rectangle like shape has two swiping curves and my 2 amps would fit if we’re all square corners.
I missing about 1” space to...
After only 250 miles this Bronco needs audio upgrade
this is going to be my only second upgrade after I did few years back in my Xterra
Components used for this project :
front stage 3way
Hertz Mille Legend MLK 1650 6.5 woofers
Rainbow Germanium Gl M3 midrange
Audison Voce AV 1.1...
Hello ,
have question to anyone who owns Bronco with capable front bumper
my plan was to mount low profile bull bar on to the fender itself with 3 7” round fog lights. I know from photos the steel bumper ( upgrade ) has 4 threaded holes ready for it , but Capable bumper is very different in...
Hello , glad to find this great forum and hope to learn some tips from other members.
We are waiting to pick up ne Bronco Black Diamond ( full size 4 Dr ) sometime in few months and I have question in reference to hard top roof rack system.
I wanted to ask if anyone here have mounted or...
Hello , glad to find this great forum and hope to learn some tips from other members.
We are waiting to pick up ne Bronco Black Diamond ( full size 4 Dr ) sometime in few months and I have question in reference to hard top roof rack system.
I wanted to ask if anyone here have mounted or...