What did you do TO / WITH your Bronco today? 👨🏻‍🔧🧰🚿🛠

[shawn6107]

Installed a wireless winch remote and tinted my outside pod lights amber. Took a couple attempts on the first one to figure out the vinyl application but I’m really happy with the results. On the wireless remote install, it was much easier than expected since the RC control box had the spade connectors already there for it.

It’s also nice that the tint matches my pinstripes perfectly . Got lucky there

Sponsored

 

[Paul Gagnon]

I am at a charity fundraising pancake breakfast at the Villeneuve Airport. I was one of the first cars here so I decided to park inside the hanger.

 

[BroncoSarge]

Finalized the winch setup with an Agency 6 winch shackle. Kept it black so it doesn't draw attention from the B R O N C O. Not really a mod, but also added door hand cups.

 

[Lifeliberty]

added door hand cups.

Ijust added the plates that stick on the bottom of the handle, where did you get the cups? That would be better

 

[22luxobx]

what train horns do you have and where did you mount them? I would like to do same thing but just dont know what kit to get and where to install them. Thank you!

 

[CCMDoc]

In addition to all of the stuff in my earlier posts on this thread, today I added

- these nifty covers over the rear defroster wires
- Rough Country tailgate reinforcement (probably switch to Hammerbuilt w accessories I’ll buy later from another Bronco6g member))
- OEM roof rack bought from another Bronco6G member (thanks Tom)

I wish someone with a 3D printer could recreated the plastic towers on the rear end of the oem roof rack.
I plan to buy an additional pair of crossbars - one for the existing additional spot along the oem rails.
The other - I’d like to recreate the clamping mechanism of the oem rail and put the 3D printed plastic covers (if they could be made) over them along with that crossbar.

I’ve asked Valkyrie if they’ll sell just one bar but haven’t gotten a response.

 

[BroncoSarge]

Ijust added the plates that stick on the bottom of the handle, where did you get the cups? That would be better

Wife got those. They feel like they are not secure. We are getting her a set like mine.

Door handle storage by Muslogy

 

[tomtouchdowns]

Confirmed that some F-150 tow brackets from Rough Country will fit. Threw two shackles on it and brought a little symmetry back to my Bronco!

 

[kevin.gt]

Finished building the sub box. Now just waiting for the rest of the equipment to install.

I need more details. This looks fantastic. Do you have a write up? Down firing plus passive radiator? Amp in the box or tucked elsewhere? How tall vs. the height of the seats when then are down?

 

[shawn6107]

Added a little shield over my relocated front camera.

Fabricating a shield for my relocated camera


I made a video of fabbing it up in case anyone wants to replicate it or improve on it.

may interest you @Bird Dog Overland

 

[Donkeygyrl]

Had to test my blow off valve .

 

[WmSikes]

Brought her home!

 

[mpeugeot]

What did I do today?

I added Keyless Remote Entry to my Bronco... Using a $100 J2534 Interface and FDRS Software.

 

[MannyG20]

Finally fixed the broken tabs on the soft top.

 

[greatlakes]

I need more details. This looks fantastic. Do you have a write up? Down firing plus passive radiator? Amp in the box or tucked elsewhere? How tall vs. the height of the seats when then are down?

Thanks! It's a sealed, down-firing, 10-inch enclosure with a separate beauty panel. I know a ported box would have more output, but I've always loved sealed enclosures. I plan on mounting the amp in the rear where the factory B&O sub would have been.

I will have to measure how much higher it sits than the seats. I've actually never had a reason to fold them down.

If there is interest, I could do a quick write up, but have not to this point.

Brian

Sponsored