DIY: Raptor Fog Lights Installed on Standard Bronco

[CarbonSteel]

Unfortunately, I don't remember where I purchased those connectors from. I couldn't find them on aliexpress back then. I had spent a lot of time browsing the web until I came across the needed connector. That's why I suggest buying the CrystaLux wire harness and adding 4-pin connector to it.

But for sure it is a 2 pin MX 150?

@flip ^^ any clues?

Sponsored

 

[2door]

But for sure it is a 2 pin MX 150?

@flip ^^ any clues?

Yes, I'm 100% sure that it's MX-150.

 

[2door]

I managed to dig out the receipt in my mailbox.
I purchased these connectors here.

 

[CarbonSteel]

I managed to dig out the receipt in my mailbox.
I purchased these connectors here.

Ah...ok. I think those ^^^ are these - thanks for digging them up.

 

[2door]

Ah...ok. I think those ^^^ are these - thanks for digging them up.

Yup, it's them. You need the male connectors though

 

[CarbonSteel]

Yup, it's them. You need the male connectors though

Yep, grabbed 4 of everything to build a few. $24 for all of them to the door. Given they are pre-wired, it should be a snap to assemble.

 

[thenewjs]

I upgraded my BRaptor Fogs with 3 rigids and put the Braptor fogs on the wife’s 2 door back in December. I was going to build my own harnesses but I already had too many projects going on. So, I bought harnesses from SPV.

 

[CarbonSteel]

@2door - does tightening of the bolt spread the folded ears on the clip?

Just want to set my expectations.

 

[2door]

@2door - does tightening of the bolt spread the folded ears on the clip?

Just want to set my expectations.

Yes, that's how these clips work.

 

[CarbonSteel]

Yes, that's how these clips work.

Thanks man. Getting closer, received all my Ford parts on Friday. Need to have the main body of the bumper painted and receive the Molex from AliExpress and I will be neck deep.in it.

 

[2door]

Thanks man. Getting closer, received all my Ford parts on Friday. Need to have the main body of the bumper painted and receive the Molex from AliExpress and I will be neck deep.in it.

No problem! Hope you're having fun putting all these pieces together

 

[CarbonSteel]

@2door - apologies for another question. What would you say the minimum length for the pigtails would need to be?

I want to offset my heat shrink butt connectors, but don't want to cause the wires to be too short. Each side has about 5" of wire.

I have the capable bumper with fog lights so not sure if that means I have more OEM wire to play with or not.

 

[2door]

@2door - apologies for another question. What would you say the minimum length for the pigtails would need to be?

I want to offset my heat shrink butt connectors, but don't want to cause the wires to be too short. Each side has about 5" of wire.

I have the capable bumper with fog lights so not sure if that means I have more OEM wire to play with or not.

Sorry, I can't give you the exact numbers. The total length of the wire harness connecting the fog light and the outlet connector needs to be around 15-16 inches. Hope this helps.

 

[tilebroncodude]

Great post! New bronco owner here, i just grabbed a bronco big bend that someone special ordered and bailed on for an awesome price. Its pretty basic but does have a modular bumper and i wanted to add factory fogs, I like to keep my mods oem if possible can they be added and can the light switch be replaced for the one with the fog ability? Has anyone performed this mod? Sorry for dupe posting and not trying to thread jack either

 

[2door]

Great post! New bronco owner here, i just grabbed a bronco big bend that someone special ordered and bailed on for an awesome price. Its pretty basic but does have a modular bumper and i wanted to add factory fogs, I like to keep my mods oem if possible can they be added and can the light switch be replaced for the one with the fog ability? Has anyone performed this mod? Sorry for dupe posting and not trying to thread jack either

Does your Bronco have the front parking sensors?

Sponsored