FIRST LOOK: Flush Style LED Tail Lights for the 2021+ Ford Bronco from ORACLE Lighting

[wafiz]

666


No pics but do not install the brackets. They include double sided tape.

Remove the red tape and stick to the side of the BLIS without the wire. (in the red box)

Grab a zip. Towards the top the BLIS has an opening to remove it. Slide a sip through the side of the blis and go around the oracle resistor. (yellow line below)

Done. It won't move, and doesn't impact the BLIS or wiring. The panel slides right behind it when reinstalling.

Paint skills below.

Thanks ! Will try it now

Sponsored

 

[Fencelizard]

Thanks Man, those washer were the fix... 100% better fitment

I had some leftover washers from my flat screen mount, thank you. They worked perfectly. I just put a dab of silicone glue on the back of them and positioned them over the light holes. Now the driver side is perfectly flush with the body. I also spoke to Oracle and they gave me the correct codes so that my lights work perfectly as well.

 

[Eljudio]

Here is what I have currently:

Hi @OracleLights any updates on the forscan edits as currently neither your install video or this post inputs doesn't work on my wild trek 2021

 

[OracleLights]

Hi @OracleLights any updates on the forscan edits as currently neither your install video or this post inputs doesn't work on my wild trek 2021

Some of our team members are still returning from SEMA. Nathan, our videographer, drove the Bronco from Vegas to NOLA! He should be in tomorrow and we will let you know when its complete!

 

[broncorik]

Hi @OracleLights any updates on the forscan edits as currently neither your install video or this post inputs doesn't work on my wild trek 2021

You tried these?

Left rear stop and position light usage - stop and turn
Right rear stop and position light usage - stop and
turn
Left turn lamp usage = not used
Right turn lamp usage = not used
Rear LED turn outage = disabled

 

[Eljudio]

I’ll try it out to tomorrow but as of now my settings which works fine for me now while I was playing around with the settings is


Left rear stop and position light usage - stop and turn
Right rear stop and position light usage - stop and
turn
Left turn lamp usage = stop turn
Right turn lamp usage = stop turn
Rear LED turn outage = disabled

 

[broncorik]

I’ll try it out to tomorrow but as of now my settings which works fine for me now while I was playing around with the settings is


Left rear stop and position light usage - stop and turn
Right rear stop and position light usage - stop and
turn
Left turn lamp usage = stop turn
Right turn lamp usage = stop turn
Rear LED turn outage = disabled

Hopefully Oracle will publish an official settings guide ASAP...weird that yours works with those settings and mine work with the other ones...you have signature lighting and removed the resistors?

 

[Eljudio]

Hopefully Oracle will publish an official settings guide ASAP...weird that yours works with those settings and mine work with the other ones...you have signature lighting and removed the resistors?

I followed the instructional video they have on YouTube very diligently on YouTube that they provided but It was annoying though that they never mentioned in the video about the blind spot monitor being in that position but I’m assuming they didn’t know that.
I have the signature light too

 

[broncorik]

I followed the instructional video they have on YouTube very diligently on YouTube that they provided but It was annoying though that they never mentioned in the video about the blind spot monitor being in that position but I’m assuming they didn’t know that.
I have the signature light too

But without resistors the BLIS units are not in the way of anything... did you run into any issues with them where they are located?

 

[JP_Oracle]

Hey everyone!

All instructions/videos regarding FORscan settings have been updated across all platforms. Again, we apologize for the mix-up & thank everyone who posted the correct settings here!

 

[broncorik]

Hey everyone!

All instructions/videos regarding FORscan settings have been updated across all platforms. Again, we apologize for the mix-up & thank everyone who posted the correct settings here!

Thanks! Can you post a link to the video and or written instructions?

 

[JP_Oracle]

Thanks! Can you post a link to the video and or written instructions?

 

[Eljudio]

You tried these?

Left rear stop and position light usage - stop and turn
Right rear stop and position light usage - stop and
turn
Left turn lamp usage = not used
Right turn lamp usage = not used
Rear LED turn outage = disabled

Tried this and it works @OracleLights you should def credit him with the purchase as he solved this whole debacle of instructions

 

[JP_Oracle]

Tried this and it works @OracleLights you should def credit him with the purchase as he solved this whole debacle of instructions

Thank you for pointing that out!

 

[ORACLE Lighting]

A few photos from SEMA with the tail lights installed!

Sponsored