What did you do TO / WITH your Bronco today? 👨🏻‍🔧🧰🚿🛠

[Jmertz21]

get tube doors. problem solved

Sounds silly but I’ve never loved the look of tube doors. You got any you really like?

Sponsored

 

[Richterman]

mabett. $400

Sounds silly but I’ve never loved the look of tube doors. You got any you really like?

Mabett $400

 

[mpeugeot]

Installed the Ford Performance Tune
Conditions: Full tank of gas, 100 lbs of tools, and 120 lbs of hidden winch mount. 75 degrees, 1900 feet above sea level. Mode: Sport 4A, launch at 1900 rpm.

0-60: 6.4 seconds
1/4 mile: 15.02@93MPH

That seems reasonable, I am sure that another run and I can be in the 14's. I only did one run so far.

 

[V1Rotate]

Swapped in a new OEM driver’s side half shaft after getting tired of chasing a previously self-induced cut in the inner CV boot thats been slinging grease for a while. Wanted to go w/ Spicer extreme 32 splines into a new ultimate 44 FDU but just can’t make the numbers work yet. Took about 1h15m with a little helper as pictured

 

[joeb]

Swapped in a new OEM driver’s side half shaft after getting tired of chasing a previously self-induced cut in the inner CV boot thats been slinging grease for a while. Wanted to go w/ Spicer extreme 32 splines into a new ultimate 44 FDU but just can’t make the numbers work yet. Took about 1h15m with a little helper as pictured

Hey, post this in the Bronco Dog thread. Would be a great addition!

 

[Bmadda]

Core 4x4 trailing arms. Still waiting for the panhard bar. Put Barnes shock skids too. Yes I nerfed up the powdercoat a little tightening them, but they are gonna get some rash sooner of later! Better they stay tight!

 

[Mike T]

Finally put wheels and tires on that I picked up off of Craigslist and used my Factory license plate bracket to install plates that showed up. Did not mount it the way it was suppose to go and I think it turned out pretty decent looking.

 

[Bruinsfan]

Installed a tailgate table from Rockslide Engineering. Easy install with six screws. We'll see if the screws back out over time. I was able to hide a cutting board inside the unit when folding away. I'm happy with it and no rattles.

 

[Grumpy]

Received another (5th) Overall Best of Show in my division today!

 

[TKE_273]

HOT today in the Midwest, but a great day for a car show.

My father works at my hometown Ford store, and they hosted a car show today to benefit the local American Cancer Society chapter. Today was the first time I've removed the rear section of hardtop, and it was easier than I anticipated!

Here's a shot of my dad's low mileage Mustang California Special next to my Bronco

Oh, and I was the judge for the show, and gave Best of Show to a PRISTINE custom 72 Bronco that I couldn't stop drooling over. The owner also has a 6G 2-Door Bronco as well, so we bonded over that.

 

[AKBronc49]

Mine is sitting in the garage, clean, waiting for the weather to be HALF DECENT. I'd love to be able to pull the top off. We've had two 60 degree days this year, it's been overcast, depressing and cold. I'm ready to book tickets to Phoenix....

 

[BeerRunner]

The wonderfully awesome folks at Gulches 4x4 park in Waterloo, SC helped this newbie in a stock bronco do some challenging (to me at least) trails. I was on the fence for upgrading more than the bumper I put on and now I know for sure it’s more capable already than I’ll ever need it to be. By the way, the one pedal hill control is amazing!

 

[BinderBill]

Finished up painting my steelies….

 

[PullMeOverRed22]

Now on 38s.

That is a sweet ride!

 

[Hoss360]

Hit a cars and coffee this morning... my 6th gen made friends with a 1st and 2nd gen

Sponsored