Are the Raptor roll bar braces available for standard Bronco?

[fordracefan]

All,

On the Bronco Raptor I believe there are 2 stiffeners/braces for the roll bar to reduce flex. I think there is one that is at the top of the roll bar and I’ve seen in pictures of an X type brace that goes across the back of the roll bar where it starts to slope down.
Are these available to purchase from Ford? I didn’t see them on the performance part page. I assume if available these would fit the standard 4 door Bronco.

Sponsored

 

[flip]

Front N2DZ-78502A74-A Available
Rear N2DZ-7850217-A Backordered
Rear bracket N2DZ-7841304-B Backordered
Front bolts W505496-S450B
Rear bolts/nuts W721872-S450B W721844-S450B W520823-S439

 

[fordracefan]

Front N2DZ-78502A74-A Available
Rear N2DZ-7850217-A Backordered
Rear bracket N2DZ-7841304-B Backordered
Front bolts W505496-S450B
Rear bolts/nuts W721872-S450B W721844-S450B W520823-S439

Thank you very much!

 

[flip]

I didn't post prices because it's embarrassing what Ford wants for them.

 

[SS Bronco]

I just built one to fit the soft top, haven’t tried it on a hard top. Definitely tightens up the whole body. Going to put it to test next week in Baja. If I am happy with the improvements may start to sell them. Great place to install interior lights also. I think ford wants over $2k for factory.

 

[FleshTuxedo]

I just built one to fit the soft top, haven’t tried it on a hard top. Definitely tightens up the whole body. Going to put it to test next week in Baja. If I am happy with the improvements may start to sell them. Great place to install interior lights also. I think ford wants over $2k for factory.

That's sick! Any chance these could work for a 2dr?
Not near my Bronco at the moment so can't see if there's a place for it.

 

[SS Bronco]

That's sick! Any chance these could work for a 2dr?
Not near my Bronco at the moment so can't see if there's a place for it.

I don’t know but when I get back I will get with my friend with a two door and find out.

 

[flip]

Don't know for sure. I couldn't find a part number for the brackets for the front braces but don't know that they're different from the standard ones. The rear likely uses the existing bolts in the bar but again, don't have one to compare it to.

 

[flip]

 

[Fonz54]

I didn't post prices because it's embarrassing what Ford wants for them.

I checked the pricing on line and it's a whopper - $2323.24! BOHICA!

 

[flip]

I checked the pricing on line and it's a whopper - $2323.24! BOHICA!

Yup and the fact that some is on back order with no eta from the supplier makes it unobtanium.

 

[Fonz54]

I think that "Unubtanium" should be a weapon in super hero movie!

I would try this one from KHC OffRoad at $375 and see how this works solo from a flex perspective.

https://khcoap.com/products/bronco-6g-body-brace

 

[Medic2586]

That's sick! Any chance these could work for a 2dr?
Not near my Bronco at the moment so can't see if there's a place for it.

I just built one to fit the soft top, haven’t tried it on a hard top. Definitely tightens up the whole body. Going to put it to test next week in Baja. If I am happy with the improvements may start to sell them. Great place to install interior lights also. I think ford wants over $2k for factory.

When you build them, send some pics and I may be interested... the Ford coast is ridiculous

 

[Ksjrb03]

All the holes are there. No difference between a bronco and Raptor body.

Sponsored