Bigger Meats. 2-Door Bronco Rolling on 40s

[BigMeatsBronco]

that's exactly how Pratt looked in school! (yes we went to same one) he used to come over to our mud bogging parties, one time his then girlfriend, got too drunk and tried to leave party, we all tried to get her car keys away from her especially Chris...the stubborn girl sneaked off anyways and didn't even make it outta my driveway before totaling her dad's ranger. plowed right into my buddies dump truck! ROFL.

Chris was ecstatic we waited untill the sober next morning to report to her dad's insurance Co.

back then I had a Chopped samurai with a SHORTENED wheelbase, and super waterproofing. we would take turns driving it through neck deep pond, only our heads and snorkel tube sticking above water!

good times. too bad he ain't got a bronco (or maybe he does)

Sponsored

 

[Fly]

that's exactly how Pratt looked in school! (yes we went to same one) he used to come over to our mud bogging parties, one time his then girlfriend, got too drunk and tried to leave party, we all tried to get her car keys away from her especially Chris...the stubborn girl sneaked off anyways and didn't even make it outta my driveway before totaling her dad's ranger. plowed right into my buddies dump truck! ROFL.

Chris was ecstatic we waited untill the sober next morning to report to her dad's insurance Co.

back then I had a Chopped samurai with a SHORTENED wheelbase, and super waterproofing. we would take turns driving it through neck deep pond, only our heads and snorkel tube sticking above water!

good times. too bad he ain't got a bronco (or maybe he does)

Haha holy shit that’s hilarious, I didn’t know that you went to school with him but his expression seemed perfect to describe your pics

 

[Tex]

Just out of curiosity, what's the bed and back of the cab look like?

 

[BigMeatsBronco]

Just out of curiosity, what's the bed and back of the cab look like?

like this...Ill post another with the bedliner later.

 

[BigMeatsBronco]

In preparation for Moab I did some fairly MAJOR trimming, and raised the front flairs 2"+

also slapped on a set of Metaltech rock sliders.

nothing rubs at full stuff, (other than the frame rail at full lock) so I'm gonna drop the front end down 6/10 " ... then lift will be only 1.5 " above SAS ride height. perfect for 40s and a low squatty look. ( NO BODY LIFT!)

here's pics....

 

[BigMeatsBronco]

Doing this requires the following fabrication at a MINIMUM.

raise battery mount 1.5"

raise coolant tank 2 "

raise Passenger side module

raise airbox 3/4 in

move wires on both inner fenders

trim upper front body mounts

cut off radiator secondary stiffeners on both sides

relocate horns

trim 1-2" on inner front fenders

the rear requires minimal trimming 1 " or so...

 

[Aztec1382]

Woah
Nice sawzall work

 

[BigMeatsBronco]

here's an idea of what needs cut.

 

[Snacktime]

Hammer time!

 

[Snacktime]

How much offset do you think you need to clear the frame? Are we talking an 1" or 4"?

 

[Bikeric]

When will the BigMeats40’s Kit be available to the Public??

 

[Tex]

like this...Ill post another with the bedliner later.

SICKKKKKKK

 

[BigMeatsBronco]

How much offset do you think you need to clear the frame? Are we talking an 1" or 4"?

I tried 1.5 spacers for about 5 min....didn't fix this because the spacers just add scrub radius...as much as clearance, so it was a wash. the solution is longer A arms....

I'll be trying out Braptor Front UCAs and LCAs soon.

 

[Bentpushrod]

In preparation for Moab I did some fairly MAJOR trimming, and raised the front flairs 2"+

also slapped on a set of Metaltech rock sliders.

nothing rubs at full stuff, (other than the frame rail at full lock) so I'm gonna drop the front end down 6/10 " ... then lift will be only 1.5 " above SAS ride height. perfect for 40s and a low squatty look. ( NO BODY LIFT!)

here's pics....

In my humble opinion, you have the sweetest 6g Bronco out there!

 

[Tex]

I tried 1.5 spacers for about 5 min....didn't fix this because the spacers just add scrub radius...as much as clearance, so it was a wash. the solution is longer A arms....

I'll be trying out Braptor Front UCAs and LCAs soon.

Come on man, where's your sense of adventure?
It's obvious you have the tools to cut a clearance notch in your frame LOL

Sponsored