Who Makes a Good Offroad Flag and Pole for Wheeling?

[Roll Sound]

I bought a flag mount today from Bronco Graveyard. Who makes a rad flag and pole combo for offroading? What are your recommendations?

Sponsored

 

[seanoj]

Thanks to your post I discovered Bronco graveyard and this product. This is exactly what I wanted to fabricate, but don't have time to...

For others looking: https://shop.broncograveyard.com/2021-Bronco-Flag-Mount/productinfo/B147100/

I got this flag, and it seems pretty decent to me. Yet to put it to the test.
https://www.amazon.com/gp/product/B07YSY6QT1

 

[Roll Sound]

Finally had time to install my flag mount today.

 

[nottinbe]

Finally had time to install my flag mount today.

Did it come black? The photo on the product page shows it in stainless.

 

[Roll Sound]

Did it come black? The photo on the product page shows it in stainless.

No, I painted it black to match guides. It came raw stainless.

 

[seanoj]

Just hit mine with the first coat of rattle can...

I am adding more washers because the flag I got has a mounting bracket that needs a half inch thick bracket...

 

[85_Ranger4x4]

Amazon special works for me:

https://www.amazon.com/gp/product/B001IQ2GSO/ref=ppx_yo_dt_b_asin_title_o00_s00?ie=UTF8&psc=1

I have the Tusk clamp mount for it too.

I will be getting the same for my wife's Bronco.

I have had friends with multipart poles and they have had problems with them staying together. I don't know what exact ones they have, maybe their are better ones out there. I got the one and it seems to do flag things pretty well so I have never tried any others.

 

[seanoj]

Agree on multipart being less reliable than a single. I just needed (I thought) an 8 foot pole when I ordered it. Was going to fab a mount off the bumper and didn't want to get into any discussions with the rangers about flag height. A single 8' pole felt a little unwieldy in storage and transit so I got the two piece.

If I had to do it again, which I probably will, it will be a 6' single, like the one you linked to.

Installed photos attached. I did only link the two piece pole together in a minimal fashion for the photo. Seems like it would take two people to disconnect it, tug of war style if it were connected fully...

 

[Hkak45]

Amazon special works for me:

https://www.amazon.com/gp/product/B001IQ2GSO/ref=ppx_yo_dt_b_asin_title_o00_s00?ie=UTF8&psc=1

I have the Tusk clamp mount for it too.

I will be getting the same for my wife's Bronco.

I have had friends with multipart poles and they have had problems with them staying together. I don't know what exact ones they have, maybe their are better ones out there. I got the one and it seems to do flag things pretty well so I have never tried any others.

Did this threaded pole fit properly in the bronco graveyard mount?

 

[Hkak45]

Just hit mine with the first coat of rattle can...

I am adding more washers because the flag I got has a mounting bracket that needs a half inch thick bracket...

Do you happen to know what size bolt is needed on the flag pole to fit that opening? 1/2 inch?

 

[Beach_Bum]

Do you happen to know what size bolt is needed on the flag pole to fit that opening? 1/2 inch?

1/2 inch as shown in another thread.

 

[bmclain]

Some places only allow orange flags. Haven't heard of anyone requiring anything different, so I got this one: https://www.handyflag.com/product-page/bronco-handy-flag-kit-orange

 

[Hkak45]

1/2 inch as shown in another thread.

Thank you! I searched but apparently didn't put the proper terms in it

 

[Hkak45]

Some places only allow orange flags. Haven't heard of anyone requiring anything different, so I got this one: https://www.handyflag.com/product-page/bronco-handy-flag-kit-orange

That looks great and I like how it folds up small. Have you used it on any trails? Does it seem to be sturdy to not break and the places where they connect?

 

[Jim Walter]

Wish I had seen this mount sooner...would have used it to mount my GMRS antenna.

Sponsored