Zone Offroad 3" 3.5" and 4" Lift Kits for 2021 Bronco (Sasquatch and Non-Sasquatch)

[BingoBangoBronco]

Bronco finally came in and the zone 4” lift arrived one week beforehand. I’m very happy with the stance and way it drives.

Can't wait to do the white black and red scheme on mine once Ford finally builds it haha getting the Fuel Contras in red.

Sponsored

 

[Beilen77]

Can't wait to do the white black and red scheme on mine once Ford finally builds it haha getting the Fuel Contras in red.

I almost went with the same fuel wheels, but wasn’t sure if I wanted that much red. I bet it’ll look great!

 

[Lurker B6G]

TBH, it rides just as good as stock IMO. I forget the KM3s are even there, lol. The biggest difference by far is getting in/out of the truck for me. Ordered the Rock Slide Engineering sliders to help with that. My 0.75" Bora hub centric spacers have shipped, so the UCA clearance issue will be resolved shortly.

On another thread it has been confirmed that 1.0" BORA spacers fit without trimming the studs. The front studs are flush with the spacer, and the rear studs stand proud by 3/16" (which fits fine in the wheel pockets). Please let us know how the 7/8 inch work - the back set may be tight with 5/16" of stud sticking out (although I think I remember reading that the pocket is about 1/2 inch deep - so hopefully you will be fine). Thanks.

 

[Bird Dog Off Road]

On another thread it has been confirmed that 1.0" BORA spacers fit without trimming the studs. The front studs are flush with the spacer, and the rear studs stand proud by 3/16" (which fits fine in the wheel pockets). Please let us know how the 7/8 inch work - the back set may be tight with 5/16" of stud sticking out (although I think I remember reading that the pocket is about 1/2 inch deep - so hopefully you will be fine). Thanks.

With the recesses in the factory Sasquatch wheels, they will fit without issue.

 

[Bird Dog Off Road]

Got the Bora 0.75" hub centric spacers on today and all is great!!!
Plenty of clearance with the UCAs now and still plenty of clearance with the crash bar mounts.

The recess in the stock Sasquatch wheels between the lugs is 3/4" deep. The factory lugs only stick out about 1/4" from the spacers. So I had ~1/2 of clearance after the install. NO changing lugs or trimming them shorter.

 

[SnowBronco]

Got the Bora 0.75" hub centric spacers on today and all is great!!!
Plenty of clearance with the UCAs now and still plenty of clearance with the crash bar mounts.

The recess in the stock Sasquatch wheels between the lugs is 3/4" deep. The factory lugs only stick out about 1/4" from the spacers. So I had ~1/2 of clearance after the install. NO changing lugs or trimming them shorter.

What are you're thoughts on the CV angle now?! On full droop? I have an icon 3" kit with upper controls and a track bar on order.... I was told with these kits that they wouldn't allow for over extension of the CV angle.

 

[Bird Dog Off Road]

I think a 3" over Sasquatch or 4" over base is the limit without using a diff drop. Different people have different opinions on this of course, but time will tell what is the limit truly is. So far, I've not heard of any CV issues, mostly tie rod and steering issues. I do have the Bronc Buster steering rack bushing and tie rod splints installed to help address those issues.

 

[rguest3]

Bird Dog - So with the Factory Sasquatch Wheel at +30 offset and the 3/4" Spacer installed, is the overall Offset now about +12?

It's interesting how the Original Sasquatch Wheels have the Recessed area???

 

[Bird Dog Off Road]

Bird Dog - So with the Factory Sasquatch Wheel at +30 offset and the 3/4" Spacer installed, is the overall Offset now about +12?

It's interesting how the Original Sasquatch Wheels have the Recessed area???

Most wheels have those recesses. My stock 4Runner wheels and the aftermarket one I had on it both did as well.

I am getting 10.95+ offset with the metric converter app on my phone.

 

[rguest3]

Do you have a par number for the Bora 3/4" spacers you installed?

Thanks for the info.

 

[Bird Dog Off Road]

Do you have a par number for the Bora 3/4" spacers you installed?

Thanks for the info.

You have to order them through their website: https://www.motorsport-tech.com/bora.html

 

[daacree]

having to get spacers for mine as I had rub at control arm when wheel is turned all the way to right and left. I place some details with video on thread.

Hello Omar... did you get your bora spacers yet? If so, what size did you end up going with and how they working out?

 

[Dubsesd]

Anyone having vibration/ chatter under slight or heavy acceleration while in 4A? I have installed mine and while on 4A it has a vibration.

 

[John 0874]

Mine does that on my sasquatch and I have not installed lift yet all stock . Not sure if it is normal.

 

[Bird Dog Off Road]

Anyone having vibration/ chatter under slight or heavy acceleration while in 4A? I have installed mine and while on 4A it has a vibration.

Haven’t noticed that on mine

Sponsored