Anyone have service manuals to remove rear cargo trim panels for 2 door?

[talbot]

Soon I'll be looking to fix the sub rattle and the guides to remove the trim panels in the cargo area of the 2 door would be helpful

I've seen for the 4 door, but not the 2

TIA
perhaps @flip?

Sponsored

 

[flip]

Soon I'll be looking to fix the sub rattle and the guides to remove the trim panels in the cargo area of the 2 door would be helpful

I've seen for the 4 door, but not the 2

TIA
perhaps @flip?

It's essentially the same.


Removal steps in this procedure may contain installation details.

1. Remove the front scuff plate trim panel.
   Refer to: Front Scuff Plate Trim Panel (501-05 Interior Trim and Ornamentation, Removal and Installation).

1. Release the clips and remove the loadspace scuff plate trim panel.
   Use the General Equipment: Interior Trim Remover

1. Remove the load compartment floor covering tie down covers.

1. Remove the bolts and the load compartment floor covering tie downs.
   Torque: 21 lb.ft (28 Nm)

1. Remove the loadspace floor covering.

Left hand side

1. NOTE: Seats removed for clarity.
   Remove the loadspace trim panel.
   1. Release the clips.
      Use the General Equipment: Interior Trim Remover
2. 1. Feed the front seatbelt retractor and pretensioner through the opening in the loadspace trim panel.
3. 1. Disconnect the PATS rear antenna electrical connector.

Right hand side

1. NOTE: Seats removed for clarity.
   Remove the loadspace trim panel.
   1. Release the clips.
      Use the General Equipment: Interior Trim Remover
2. 1. Feed the front seatbelt retractor and pretensioner through the opening in the loadspace trim panel.
3. 1. Disconnect the PATS rear antenna electrical connector.
4. 1. Disconnect the loadspace interior rear light electrical connector.
5. 1. Disconnect the power point electrical connector.

Installation

 

[talbot]

thank you @flip!

 

[Bruno]

thank you @flip!

please send pics of whats behind these

 

[manolan478]

@flip Can you tell me which manual you got the images from? I had pulled off my panels and it appears that the clips that look like a radar dish (marked with a number 1 on the left in the last pic) are broken. I need to order a few of these but I am not sure the name of them so I can order the correct ones.

Thanks,
Milton

 

[Cygnusx1]

Just grip it and rip it. You're going to break all those white inserts no matter how gentle you tickle that trim. Buy the replacments first.

 

[manolan478]

LOL @Cygnusx1
Well, I did break some of those boogers. I just need to know what they are called so I can order them.

And how dumb of Ford to put this junk in.

 

[flip]

@flip Can you tell me which manual you got the images from? I had pulled off my panels and it appears that the clips that look like a radar dish (marked with a number 1 on the left in the last pic) are broken. I need to order a few of these but I am not sure the name of them so I can order the correct ones.

Thanks,
Milton

W721378-S300

 

[manolan478]

Well, those are quite expensive right now. I guess I will need to see if there is an alternative. Thanks for the info.

 

[Lifeliberty]

Well, those are quite expensive right now. I guess I will need to see if there is an alternative. Thanks for the info.

Thread 'Replacement clips for rear side panels' https://www.bronco6g.com/forum/threads/replacement-clips-for-rear-side-panels.38257/

 

[bcb1]

Does anyone know if you have to remove the rear seats to get the plastic panels off the sides? I don’t want to remove if I don’t have to.

 

[soupcansam]

Does anyone know if you have to remove the rear seats to get the plastic panels off the sides? I don’t want to remove if I don’t have to.

I have this question as well. Did you ever figure it out?

 

[talbot]

No you dont have to remove the seats
carefully disconnect from the attachment points and you can slide the panel out the cargo area

 

[Mikey D]

It's essentially the same.


Removal steps in this procedure may contain installation details.

1. Remove the front scuff plate trim panel.
   Refer to: Front Scuff Plate Trim Panel (501-05 Interior Trim and Ornamentation, Removal and Installation).
2. Release the clips and remove the loadspace scuff plate trim panel.
   Use the General Equipment: Interior Trim Remover

1. Remove the load compartment floor covering tie down covers.

1. Remove the bolts and the load compartment floor covering tie downs.
   Torque: 21 lb.ft (28 Nm)

1. Remove the loadspace floor covering.

Left hand side

1. NOTE: Seats removed for clarity.
   Remove the loadspace trim panel.
   1. Release the clips.
      Use the General Equipment: Interior Trim Remover
2. 1. Feed the front seatbelt retractor and pretensioner through the opening in the loadspace trim panel.
3. 1. Disconnect the PATS rear antenna electrical connector.

Right hand side

1. NOTE: Seats removed for clarity.
   Remove the loadspace trim panel.
   1. Release the clips.
      Use the General Equipment: Interior Trim Remover
2. 1. Feed the front seatbelt retractor and pretensioner through the opening in the loadspace trim panel.
3. 1. Disconnect the PATS rear antenna electrical connector.
4. 1. Disconnect the loadspace interior rear light electrical connector.
5. 1. Disconnect the power point electrical connector.

Installation

Awesome. Super helpful. Only issue was with power clip, but finally figured it out.

Sponsored