RockJock track rod bracket full suspension compression requirement

[youloze]

Here's couple measures...

3-5/8" center of axle tube mount to the top of the bracket.

2-1/2" center of axle tube mount to center of Trac bar bolt.

Hope that helps

Thank you, sir! Very kind of you.

Sponsored

 

[Tricky Mike]

The Eibachs do compress less than 18"

I wonder if the position on the threads effects the compressed length and if they publish the minimum as threaded all the way out.

Also I would think a guy should be able to add a spacer above the bumpstops like Icon has you do for 37s to reduce up travel.

 

[youloze]

I wonder if the position on the threads effects the compressed length and if they publish the minimum as threaded all the way out.

Yeah, I think that is what PWillette above was referring to as well. I'm going to most likely order it and give it a shot. I feel like I have tons of clearance with the 4" lift.

Thanks!

 

[Tricky Mike]

Yeah, I think that is what PWillette above was referring to as well. I'm going to most likely order it and give it a shot. I feel like I have tons of clearance with the 4" lift.

Thanks!

So I have the same shocks but a Boss4x4 riser, which is basically a copy of the Rock Jock as far as I can tell. I was supposed to install them last Saturday but had to cancel. So I'm interested in figuring out this too.

 

[PWillette]

Yeah, I think that is what PWillette above was referring to as well. I'm going to most likely order it and give it a shot. I feel like I have tons of clearance with the 4" lift.

Thanks!

If u want one for the sake of science I'll send u mine for USPS, probably $20. Not doing me any good.

 

[youloze]

If u want one for the sake of science I'll send u mine for USPS, probably $20. Not doing me any good.

Hell, sounds like a deal to me...for science of course

Why did you decide not to use it?

 

[PWillette]

Hell, sounds like a deal to me...for science of course

Why did you decide not to use it?

I'm only at 2" of lift and it was obvious that I was going to hit the frame with the Eibachs fully compressed.

 

[1979]

I guess I was mostly just annoyed at the short reply.

What else should they have said?

 

[youloze]

I'm only at 2" of lift and it was obvious that I was going to hit the frame with the Eibachs fully compressed.

Ahh I see. Thanks for the offer! I'll shoot you a message.

 

[akturbo]

Side note, Radflo and ADS also don't work with the bracket.

 

[youloze]

Side note, Radflo and ADS also don't work with the bracket.

I'm starting to wonder what does at this point lol. PWillette was gracious enough to send me the bracket for the cost of shipping (thank you again!), so I installed it and will see if it makes contact the next time I have a chance to go off-road. I think with my 4" lift I should be ok.

 

[akturbo]

I'm starting to wonder what does at this point lol. PWillette was gracious enough to send me the bracket for the cost of shipping (thank you again!), so I installed it and will see if it makes contact the next time I have a chance to go off-road. I think with my 4" lift I should be ok.

Icon, Fox and King would clear.

 

[Mikerider]

as an alternative you could try the OME bracket

https://store.arbusa.com/rear-panhard-relocation-bracket-fk109/

It mounts differently so no compressed length restriction from what I have found.

 

[youloze]

as an alternative you could try the OME bracket

https://store.arbusa.com/rear-panhard-relocation-bracket-fk109/

It mounts differently so no compressed length restriction from what I have found.

Thanks for the link. Looks like it is only for use with the OME bar per their site though?

 

[Mikerider]

Thanks for the link. Looks like it is only for use with the OME bar per their site though?

I considered that but they don’t sell a track bar yet for the bronco.

worked fine for me with the stock bar

Sponsored