Winch setup For Modular HD Bumper?

[mrock]

Has anyone set up an after market winch on the HD Modular Bumper? I don't want to switch out bumpers, and the Ford products seem stupid expensive. Thanks

Sponsored

 

[Hemisfear]

Has anyone set up an after market winch on the HD Modular Bumper? I don't want to switch out bumpers, and the Ford products seem stupid expensive. Thanks

This is the ANMOSVO Winch mount I found on Amazon. Drilled 2 1-1/8" holes on the front edge of the plate for the parking sensors and it works with ACC, camera relocation coming soon!
Pretty much exactly what I wanted and most likely one o0f the lightest set ups!

 

[‘21OBX]

Rough country has one out as well that I installed on mine. Comes with wiring and sensor mounts as well.

 

[mrock]

Thanks

 

[smahones]

Has anyone set up an after market winch on the HD Modular Bumper? I don't want to switch out bumpers, and the Ford products seem stupid expensive. Thanks

The JCR winch mount is great in the mod bumper. It rides halfway up the bumper so the clearance loss when climbing rocks is minimal. I relocated the camera to the front as well as the bumper sensors.

 

[KPLOBX]

Is the JCR 100% bolt on? I’m looking for a solution I can install when I’m ready to wheel and remove when I’m driving daily.

how about the ANMOSVO Winch mount?
Are either/both of these easy to R&R?

 

[Tricky Dick]

I forget what brand it was, but what @66GT has is my favorite so far. Hopefully he'll chime in.

 

[Northridge4x4]

The Rough Country winch mounts have been pretty popular for us.

https://www.northridge4x4.com/part/winch-accessories/51067-rough-country-high-winch-mount-black

 

[66GT]

I forget what brand it was, but what @66GT has is my favorite so far. Hopefully he'll chime in.

The Rough Country winch mounts have been pretty popular for us.

https://www.northridge4x4.com/part/winch-accessories/51067-rough-country-high-winch-mount-black

I run the RC high-mount with a Badland Apex 12k (with the control box relocated under the hood).

It mounts on top of the mod bumper... and is set back towards the grille to preserve the approach angle.

Fabbed up a bracket and faceplate to relocate the camera underneath the winch... works just fine with all the lux pkg stuff... including ACC and parking sensors.

Have no doubts about its strength... have used it to recover a Tacoma with 33s that was almost tire-deep in muck.

 

[Northridge4x4]

Nice! and love the camera relocation.

 

[cricex]

Is the JCR 100% bolt on? I’m looking for a solution I can install when I’m ready to wheel and remove when I’m driving daily.

how about the ANMOSVO Winch mount?
Are either/both of these easy to R&R?

This is what I want to accomplish as well - which also implies no camera relocation while leaving the camera usable for trails.

 

[JWBroncoATL]

I run the RC high-mount with a Badland Apex 12k (with the control box relocated under the hood).

It mounts on top of the mod bumper... and is set back towards the grille to preserve the approach angle.

Fabbed up a bracket and faceplate to relocate the camera underneath the winch... works just fine with all the lux pkg stuff... including ACC and parking sensors.

Have no doubts about its strength... have used it to recover a Tacoma with 33s that was almost tire-deep in muck.

Sweet! Are you saying that you "Fabbed up a bracket and faceplate to relocate the camera underneath the winch... works just fine with all the lux pkg stuff... including ACC and parking sensors."

Or that RC sells that bracket/faceplate to make it work with all the Lux stuff?

 

[BigSkyBronco]

@66GT Bump

 

[66GT]

Sweet! Are you saying that you "Fabbed up a bracket and faceplate to relocate the camera underneath the winch... works just fine with all the lux pkg stuff... including ACC and parking sensors."

Or that RC sells that bracket/faceplate to make it work with all the Lux stuff?

@BigSkyBronco

I fabbed up the bracket to relocate the camera (removing the "RC" with a dremel tool). Made a separate top plate to "sandwich' the mount with the rear bracket.

My garage... lol.

The video feed from the new location works great. Did some beer math geometry and figured adjusting the look angle to 30° corrected for the change in height.

Also relocated the control box guts to a weatherproof project box under the hood.

Also fabbed up some brackets to snug in some 4" spots inside the OEM brush guard and coated the brightwork on the engagement lever and fairlead with a durable undercoating.

It was a little work to get it all sorted the way I wanted it, but I'm really happy with it.

 

[JWBroncoATL]

@BigSkyBronco

I fabbed up the bracket to relocate the camera (removing the "RC" with a dremel tool). Made a separate top plate to "sandwich' the mount with the rear bracket.



The video feed from the new location works great. Did some beer math geometry and figured adjusting the look angle to 30° corrected for the change in height.

Also relocated the control box guts to a weatherproof project box under the hood.

Also fabbed up some brackets to snug in some 4" spots inside the OEM brush guard and coated the brightwork on the engagement lever and fairlead with a durable undercoating.

It was a little work to get it all sorted the way I wanted it, but I'm really happy with it.

That is so cool! Great job. Wish RC just did it this way themselves! I don't need an RC logo, but I do need my front camera!

Sponsored