It won’t if you do it by adding a bit taller springs to the existing coil over…but someone needs to build them.Leveling the sasquatch puts the CV into a position that will cause it to bind at full droop. Just don't go off roading with it and you should be fine (not sure if you're making a mall crawler or a real offroader - not judging, everyone has a different reason to buy it). If you're planning on doing offroading then you're better off using a full coilover upgrade.
https://www.bronco6g.com/forum/thre...ide-lift-heights-with-wheel-tire-sizes.17719/
That stance looks perfect. It’s interesting that 4WP did the install. I went to local shop in Austin, TX and they said there isn’t currently a kit for the SAS that 4WP had approved to install? Ford dealer quoted me $500 to have the 1” Zone installed, so considering that.The Wheels and Tires are 17x9 Dirty Life Canyon Gray Wheels 35" Nitto AT Tires 6x5.5 2021 Ford Bronco off Ebay seller: auto-addicts
(I specified12.50X35R17) the ones they advertise have 315/70R17 the wheels are 0 offset 5" backspace they sent them with the Tire pressure sensors, that were already programmed for my Bronco, I literally Bolted them on Torqued to 100 ft. lbs. and done they were truck shipped on a pallet that was carefully set up and shrink wrapped including 27-splinned lug nuts and socket to mount all wheels including the spare I got them in 3 Days after order Date Very Satisfied with the entire experience as far as the 1-1/2" level kit I had it installed at 4wheelparts.com ($638.45)including a 4 wheel alignment and on a level surface it is dead-on level! and the shackles (D-rings) are from Harbor Freight and the say Badland on them APEX 3/4 in. D-Ring Shackle (harborfreight.com) I painted them orange to match also I bought: 10,000 lb. Capacity 3 in. x 30 ft. Recovery Snatch Strap (harborfreight.com) and a: Receiver Tow Hook (harborfreight.com) as well.
What wheels are those? Reminds me of the old 5-slots I had on my 79Added Zone’s 1” level kit to my Badlands Sasquatch today. It took about 3 hours.
To be completely honest I think leveling a vehicle is useless unless you only plan on mall crawling it for the look.Has anyone leveled a squatched Bronco? Not lifted front and rear, just added a small spacer or made another adjustment to get the front up to level. Mine is about 1" low in the front and I personally don't like the raked look. The whole point of going sasquatch was to have a trail ready rig that I could use and abuse until upgrading the coilovers to Kings in the future but I'd love it leveled out sooner than later. I know it is nit-picking but it's the only thing I can complain about my Bronco.
Thank-you for the complement! here is the link on the 4wp website for the kit: 2021 Ford Bronco| Fabtech 1.5" Leveling Kit - FTL5212 | 4wheelparts.comThat stance looks perfect. It’s interesting that 4WP did the install. I went to local shop in Austin, TX and they said there isn’t currently a kit for the SAS that 4WP had approved to install? Ford dealer quoted me $500 to have the 1” Zone installed, so considering that.
my Badlands 4 Dr SAS def has a 1-1.5”rake, so I want to install but so many have stated concern for bad angles and actual off road use.
either way, you have a great looking Bronco!!
Well thats kinda the question isn't it. How do you get an inch or so in front without using a spacer lift. Can the sasquatch be adjusted at the coilover?To be completely honest I think leveling a vehicle is useless unless you only plan on mall crawling it for the look.
I plan on adding gear on my trips which will sag the rear suspension and level it out. Most of the time I have something in the back like gear or kids and have never needed it. My friends Tundra is leveled and it almost feels like your leaning back and makes it harder to see out the front unless you raise your seat more.
To each their own I guess.
I'm not hating asking a real question why upgrade? Have you broke it to need upgrading or just want it?Exactly to each their own,
I am very happy with my Bronco and hopefully you are all happy with yours level or not.
I plan on installing new axles as soon as they are available anyway and in the next couple of years better suspension products will be available also
Spicer Extreme™ Half Shafts | Spicer Parts
More pics please!!!! What wheels, tire size etc.? Looks amazing!!Added Zone’s 1” level kit to my Badlands Sasquatch today. It took about 3 hours.
I see a weakness in the stock axles and as always, I am looking for stronger/better suspension parts, I will aways be ready to upgrade anything to make my Bronco Better and more reliable that is just how I roll.I'm not hating asking a real question why upgrade? Have you broke it to need upgrading or just want it?
In my years of having 4x4s never seen or broke an axle that wasn't drivers fault.
Are they longer or just stronger? Looked to just be stronger.
Do they allow for more lift because they allow for more angle.
I read all I see was stronger.
Again I'm not hating if it's just stronger, but do you get more?
What kit did you use? I’ve been looking for a badlands non sas lift kit.only found zone 1” front leveling kit.I’m adding 35” tires to my non sas BD as soon as the wheels ship. I already installed the lift (1” front, 2” rear). What is going to be the problem exactly?