B&O sound system complete upgrade - Done ✅

[Wolfeman]

Anyone know a good replacement to the recommended " 4“ speaker wire harness adapter" I can't find the ones he said to buy on amazon. Thanks!

I got two for free with my speakers. Will I only need 2 for the front dash or do I need to buy another one?

If you already got them, you should be good. These weren't available originally but Metra finally came around and started producing them.

If you have B&O and are replacing all three speakers up front, you will need an extra speaker and an extra adapter.

Sponsored

 

[Benallen6]

If you already got them, you should be good. These weren't available originally but Metra finally came around and started producing them.

If you have B&O and are replacing all three speakers up front, you will need an extra speaker and an extra adapter.

I'm base so i dont think i got B&O

 

[Donkey]

I started my overhaul of the B&O system a couple months ago, and finished buttoning it up this weekend. It’s been a long journey of trial and error, and parts returned or wasted, but I’m thrilled with the final results. I have contributed to many threads along the way, but wanted to consolidate it all into a completed build thread as I get many questions about what I’ve done.

I’ll start out with why I got started on this project. To put it bluntly, I think the B&O system is pretty bad for a “premium“ system. It’s pretty much lacking in every way, low power, muddy highs, boomy rattly bass, and really bad soundstage with most all of the sound coming from the windshield. The speakers are cheap, paper, and half of them are the same speakers used in the base system.

I would rate the system 4/10 stock, and 15/10 after upgrades. This rating is based solely on my expectations/experiences of a factory “premium” system with cost as a factor. From the factory it severely missed expectations, after upgrades it blows away my expectations, as it should. The sub kicks. I haven't had a system that can rattle the mirrors since high school. I won’t be rattling mirrors, but I could if I want

I will list the parts ”I” used. Wiring diagrams and shop manuals for removal/install are attached.

Parts

JL C1 4” - $99 pair x2
https://www.crutchfield.com/p_13699040/JL-Audio-C1-400x.html

JL C1 6.5” - $149 pair
https://www.crutchfield.com/p_13699042/JL-Audio-C1-650x.html

Focal ACX 4” - $109 pair
https://www.crutchfield.com/p_091ACX100/Focal-ACX-100.html

Kicker Comp R 8” 4ohm DVC sub - $89
https://www.amazon.com/gp/product/B08NFHJZNP/ref=ppx_yo_dt_b_asin_title_o02_s00?ie=UTF8&psc=1

Kicker Key 500.1 amp - $270
https://www.amazon.com/gp/product/B084HLH77B/ref=ppx_yo_dt_b_asin_title_o09_s00?ie=UTF8&psc=1

Kicker wired remote bass control - $39
https://www.amazon.com/gp/product/B08D3TVFBX/ref=ppx_yo_dt_b_asin_title_o08_s01?ie=UTF8&psc=1

right angle extension wire for bass control knob - $11
https://www.amazon.com/gp/product/B0793KZYXD/ref=ppx_yo_dt_b_asin_title_o03_s00?ie=UTF8&th=1

25’ 8guage copper amp wire - $25
https://www.amazon.com/gp/product/B079RZF94M/ref=ppx_yo_dt_b_asin_title_o08_s01?ie=UTF8&psc=1

8 gauge amp fuse/battery connector - $9
https://www.amazon.com/gp/product/B071ZZZK5W/ref=ppx_yo_dt_b_asin_title_o08_s01?ie=UTF8&th=1

8 gauge ring terminal for ground - $7
https://www.amazon.com/gp/product/B0747M3SYQ/ref=ppx_yo_dt_b_asin_title_o08_s00?ie=UTF8&psc=1

4“ speaker wire harness adapter - x3 - $12.99 each pair
search Amazon

Kilmat sound deadening sheets - $35
https://www.amazon.com/gp/product/B082Q2J2T4/ref=ppx_yo_dt_b_asin_title_o03_s00?ie=UTF8&psc=1

Total - $979.97

Dash Speakers

There are three 4” speakers in the dash. I used JL C1 for all three. I originally tried Focal ACX, but found them very “bright”. I ended up using the Focals in the rear pods and the JLs in the dash. This combination works great, as the bright Focal pods allow more rear fill, that was canceled out having Focals in the dash as well. This combination makes huge improvements to the overall soundstage, actually having some rear fill is an amazing improvement. Don’t skip the center channel! It’s is the workhorse up front, especially if you use surround mode.

Replacing these speakers is pretty straightforward, remove trim panel, unbolt speaker, attach harness adapter, reinstall. Shop manual attached if you need it. I highly suggest a nice set of panel removal tools so you don’t scratch up the plastic. I tossed some kilmat underneath each speaker, trying to make the hollow space underneath more of a pocket.

The center channel is a little tricky, you need to remove a screw on each side of the “accessory ready” bolt, remove that, then you can remove the speaker cover panel.

Kick Panel

I used JL C1s here as well. Honestly a 2 way speaker is not needed here in the kick panels. The DSP/amp filters out highs, this is a place you could cheap out a bit If you want. The C1s came with a trim ring mounting adapter that worked great. Crutchfield also sent a Metra adapter that I did not use, and also sent a wiring harness adapter that I did use, both free. I used Kilmat behind these speakers as well. Removing the panels is easy enough, but it’s kind of an awkward spot to work in. There is a foam section below the speaker housing you will need to make a slit in and feed the wiring through. Button everything up with zip ties. Shop manual attached.

Rear Pod Speakers

As mentioned before I used Focal ACX back here. They work great to provide some much needed rear fill. These are the easiest speakers to replace. Pop the cover off by squeezing both sides and it will pop right off. Unscrew speaker, install wiring harness, reinstall. I filled the entire cavity with kilmat again. Shop manual attached.

Sub/Amp

This is where things got interesting. I first tried to just swap the sub speaker, and long story short that was a huge fail. I tried two different subs. A $300 Rockford P3 that popped and clicked, underpowered to say the least. A $19 Pyle sub worked, but wasn’t much if any improvement over the stock sub. I took a pause here as life got busy. Then got re-interested by @cmcbronco and his great thread on installing the B&O sub enclosure on a base system. Lots of great info here.

https://www.bronco6g.com/forum/threads/b-o-sub-installed-on-base-bronco-…-sorta….37207/

I ended up going with a Kicker Comp R 4 ohm DVC sub and Kicker key 500.1 amp. I wired the sub parallel to get 2 ohm at the amp. The beauty of this amp is you can use the speaker wires going to the factory sub as high level inputs. This will also work for the power on, so no need to find a trigger on circuit. I called Kicker and confirmed the sub wires coming from the factory amp will work for high level inputs, no line output converter needed. They said this is exactly what this amp was designed for.

The Comp R sub fits the factory enclosure great, but you need to pry the plastic trim ring off with a screwdriver. No modification needed to the enclosure with this sub. Shout out to @SCTWNB for the great mounting location for the amp, I wouldn’t of thought of this location myself. It’s mounted to the roll bar, snugged in there next to sub enclosure. It is a bit tricky, but take your time, mark your holes, drill some pilot holes. Use double sided mounting tape to hold it up for install and cushion it from the body. If you plan to use this location pay close attention to where i have it, any higher and the PATS antenna mounted on the quarter panel will interfere. A right angle adapter is needed for the remote volume wire, which I installed under the HVAC controls. Wire runs down the passenger side wire channel, up kick panel, behind glovebox.

I ran 8 gauge power wire across the cargo area behind rear seats, down floor wiring panels under door, up front kick panels, and through grommet in the firewall. Fused at battery, and connected to one of the spare spots Ford gave us. Need an M5 or M6 nut here, depending which you use. Ground is wired To the factory ground found right above sub. I cut the factory sub wires that are sealed in the grommet in sub enclosure, and connected them to the high level inputs on the amp. Cut off the RCA ends, and connected them with butt connectors, make sure you get polarity correct! Wiring drawing below. I drilled holes in the same grommet to run 14g speaker wire to the sub. Apologies for the lack of installation pics on most of this, I will grab some and update later if needed.

I ended up stuffing the enclosure with PolyFil. This really helped, the bass is less boomy, hits harder and tighter if that makes sense. I had to re-adjust my preferred settings afterwards, it makes a difference. Someone that doesn’t want to bother with a sub/amp should try adding polyfil to the oem sub. I bet it helps alot.

Rattle Battle

Anyone with the B&O system knows the sub is a rattle machine at higher volumes. I had the rear panels off no less than 5 times prior to upgrade finding and fixing rattles. I had my doubts if it could ever be rattle free with an aftermarket sub and amp. I am declaring 98% victory on rattles. For my everyday listening music and volumes it’s 100% victory.

I did so much fighting rattles it’s impossible to remember and list it all. My method was simple, play certain 90s gangsta rap songs with repeated bass frequencies on loop that generate rattle everytime. Loud. When neighbors were out that turned to bass frequency sweeps and loops I found online. Play loud and go around using your ears to pinpoint and your hands to feel and absorb. What I ended up with is Kilmat in the entire cargo area, 3 rolls of cloth tape wrapping wires, connectors, insulating behind pins, wiring under rear seats, etc. Used Kilmat to insulate behind most things touching the body. Suspect panel clips were replaced (and several broken). Be diligent in your battle and you can win!

Panel clips

I started my overhaul of the B&O system a couple months ago, and finished buttoning it up this weekend. It’s been a long journey of trial and error, and parts returned or wasted, but I’m thrilled with the final results. I have contributed to many threads along the way, but wanted to consolidate it all into a completed build thread as I get many questions about what I’ve done.

I’ll start out with why I got started on this project. To put it bluntly, I think the B&O system is pretty bad for a “premium“ system. It’s pretty much lacking in every way, low power, muddy highs, boomy rattly bass, and really bad soundstage with most all of the sound coming from the windshield. The speakers are cheap, paper, and half of them are the same speakers used in the base system.

I would rate the system 4/10 stock, and 15/10 after upgrades. This rating is based solely on my expectations/experiences of a factory “premium” system with cost as a factor. From the factory it severely missed expectations, after upgrades it blows away my expectations, as it should. The sub kicks. I haven't had a system that can rattle the mirrors since high school. I won’t be rattling mirrors, but I could if I want

I will list the parts ”I” used. Wiring diagrams and shop manuals for removal/install are attached.

Parts

JL C1 4” - $99 pair x2
https://www.crutchfield.com/p_13699040/JL-Audio-C1-400x.html

JL C1 6.5” - $149 pair
https://www.crutchfield.com/p_13699042/JL-Audio-C1-650x.html

Focal ACX 4” - $109 pair
https://www.crutchfield.com/p_091ACX100/Focal-ACX-100.html

Kicker Comp R 8” 4ohm DVC sub - $89
https://www.amazon.com/gp/product/B08NFHJZNP/ref=ppx_yo_dt_b_asin_title_o02_s00?ie=UTF8&psc=1

Kicker Key 500.1 amp - $270
https://www.amazon.com/gp/product/B084HLH77B/ref=ppx_yo_dt_b_asin_title_o09_s00?ie=UTF8&psc=1

Kicker wired remote bass control - $39
https://www.amazon.com/gp/product/B08D3TVFBX/ref=ppx_yo_dt_b_asin_title_o08_s01?ie=UTF8&psc=1

right angle extension wire for bass control knob - $11
https://www.amazon.com/gp/product/B0793KZYXD/ref=ppx_yo_dt_b_asin_title_o03_s00?ie=UTF8&th=1

25’ 8guage copper amp wire - $25
https://www.amazon.com/gp/product/B079RZF94M/ref=ppx_yo_dt_b_asin_title_o08_s01?ie=UTF8&psc=1

8 gauge amp fuse/battery connector - $9
https://www.amazon.com/gp/product/B071ZZZK5W/ref=ppx_yo_dt_b_asin_title_o08_s01?ie=UTF8&th=1

8 gauge ring terminal for ground - $7
https://www.amazon.com/gp/product/B0747M3SYQ/ref=ppx_yo_dt_b_asin_title_o08_s00?ie=UTF8&psc=1

4“ speaker wire harness adapter - x3 - $12.99 each pair
search Amazon

Kilmat sound deadening sheets - $35
https://www.amazon.com/gp/product/B082Q2J2T4/ref=ppx_yo_dt_b_asin_title_o03_s00?ie=UTF8&psc=1

Total - $979.97

Dash Speakers

There are three 4” speakers in the dash. I used JL C1 for all three. I originally tried Focal ACX, but found them very “bright”. I ended up using the Focals in the rear pods and the JLs in the dash. This combination works great, as the bright Focal pods allow more rear fill, that was canceled out having Focals in the dash as well. This combination makes huge improvements to the overall soundstage, actually having some rear fill is an amazing improvement. Don’t skip the center channel! It’s is the workhorse up front, especially if you use surround mode.

Replacing these speakers is pretty straightforward, remove trim panel, unbolt speaker, attach harness adapter, reinstall. Shop manual attached if you need it. I highly suggest a nice set of panel removal tools so you don’t scratch up the plastic. I tossed some kilmat underneath each speaker, trying to make the hollow space underneath more of a pocket.

The center channel is a little tricky, you need to remove a screw on each side of the “accessory ready” bolt, remove that, then you can remove the speaker cover panel.

Kick Panel

I used JL C1s here as well. Honestly a 2 way speaker is not needed here in the kick panels. The DSP/amp filters out highs, this is a place you could cheap out a bit If you want. The C1s came with a trim ring mounting adapter that worked great. Crutchfield also sent a Metra adapter that I did not use, and also sent a wiring harness adapter that I did use, both free. I used Kilmat behind these speakers as well. Removing the panels is easy enough, but it’s kind of an awkward spot to work in. There is a foam section below the speaker housing you will need to make a slit in and feed the wiring through. Button everything up with zip ties. Shop manual attached.

Rear Pod Speakers

As mentioned before I used Focal ACX back here. They work great to provide some much needed rear fill. These are the easiest speakers to replace. Pop the cover off by squeezing both sides and it will pop right off. Unscrew speaker, install wiring harness, reinstall. I filled the entire cavity with kilmat again. Shop manual attached.

Sub/Amp

This is where things got interesting. I first tried to just swap the sub speaker, and long story short that was a huge fail. I tried two different subs. A $300 Rockford P3 that popped and clicked, underpowered to say the least. A $19 Pyle sub worked, but wasn’t much if any improvement over the stock sub. I took a pause here as life got busy. Then got re-interested by @cmcbronco and his great thread on installing the B&O sub enclosure on a base system. Lots of great info here.

https://www.bronco6g.com/forum/threads/b-o-sub-installed-on-base-bronco-…-sorta….37207/

I ended up going with a Kicker Comp R 4 ohm DVC sub and Kicker key 500.1 amp. I wired the sub parallel to get 2 ohm at the amp. The beauty of this amp is you can use the speaker wires going to the factory sub as high level inputs. This will also work for the power on, so no need to find a trigger on circuit. I called Kicker and confirmed the sub wires coming from the factory amp will work for high level inputs, no line output converter needed. They said this is exactly what this amp was designed for.

The Comp R sub fits the factory enclosure great, but you need to pry the plastic trim ring off with a screwdriver. No modification needed to the enclosure with this sub. Shout out to @SCTWNB for the great mounting location for the amp, I wouldn’t of thought of this location myself. It’s mounted to the roll bar, snugged in there next to sub enclosure. It is a bit tricky, but take your time, mark your holes, drill some pilot holes. Use double sided mounting tape to hold it up for install and cushion it from the body. If you plan to use this location pay close attention to where i have it, any higher and the PATS antenna mounted on the quarter panel will interfere. A right angle adapter is needed for the remote volume wire, which I installed under the HVAC controls. Wire runs down the passenger side wire channel, up kick panel, behind glovebox.

I ran 8 gauge power wire across the cargo area behind rear seats, down floor wiring panels under door, up front kick panels, and through grommet in the firewall. Fused at battery, and connected to one of the spare spots Ford gave us. Need an M5 or M6 nut here, depending which you use. Ground is wired To the factory ground found right above sub. I cut the factory sub wires that are sealed in the grommet in sub enclosure, and connected them to the high level inputs on the amp. Cut off the RCA ends, and connected them with butt connectors, make sure you get polarity correct! Wiring drawing below. I drilled holes in the same grommet to run 14g speaker wire to the sub. Apologies for the lack of installation pics on most of this, I will grab some and update later if needed.

I ended up stuffing the enclosure with PolyFil. This really helped, the bass is less boomy, hits harder and tighter if that makes sense. I had to re-adjust my preferred settings afterwards, it makes a difference. Someone that doesn’t want to bother with a sub/amp should try adding polyfil to the oem sub. I bet it helps alot.

Rattle Battle

Anyone with the B&O system knows the sub is a rattle machine at higher volumes. I had the rear panels off no less than 5 times prior to upgrade finding and fixing rattles. I had my doubts if it could ever be rattle free with an aftermarket sub and amp. I am declaring 98% victory on rattles. For my everyday listening music and volumes it’s 100% victory.

I did so much fighting rattles it’s impossible to remember and list it all. My method was simple, play certain 90s gangsta rap songs with repeated bass frequencies on loop that generate rattle everytime. Loud. When neighbors were out that turned to bass frequency sweeps and loops I found online. Play loud and go around using your ears to pinpoint and your hands to feel and absorb. What I ended up with is Kilmat in the entire cargo area, 3 rolls of cloth tape wrapping wires, connectors, insulating behind pins, wiring under rear seats, etc. Used Kilmat to insulate behind most things touching the body. Suspect panel clips were replaced (and several broken). Be diligent in your battle and you can win!

Panel clips and part #s

Wiring drawing

11/14/22 Edit to add modified drawing, showing wire changes color after the green connector

Shop Manuals for removing trim

I’m not where I can have access to a garage or carport at the moment and am looking for basically a straight one to one component replacement so I can avoid pulling my dash apart, etc. Did you find yourself forced into any major tear downs aside from the dynamite? I really don’t have a good way to leave things strung out overnight.

 

[Johnny Mo]

@Ksjrb03 Excellent write up thank you for convincing me to spend more money - the speaker companies should be giving you a commission.

Quick point of clarification as I see some have mentioned the CWR84 and the CWRT84 (shallow mount) did you go with the standard or the shallow mount - and thoughts on the difference given the small enclosure for B&O?

I was likely going to do all speakers and just a sub - but based on reading this whole thread - am leaning towards not doing the kick panels and getting a 500.1 to go along with the sub. I think I can mount it where I mounted my relays for my compressor rather than mount to the roll bar. The slide out tailgate gives me a little extra room under the floor to mount it.

 

[Ksjrb03]

I’m not where I can have access to a garage or carport at the moment and am looking for basically a straight one to one component replacement so I can avoid pulling my dash apart, etc. Did you find yourself forced into any major tear downs aside from the dynamite? I really don’t have a good way to leave things strung out overnight.

Speaker swap is quick and simple. Should be no problem in a Walmart parking lot. The rest needs a bit more dedication

@Ksjrb03 Excellent write up thank you for convincing me to spend more money - the speaker companies should be giving you a commission.

Quick point of clarification as I see some have mentioned the CWR84 and the CWRT84 (shallow mount) did you go with the standard or the shallow mount - and thoughts on the difference given the small enclosure for B&O?

I was likely going to do all speakers and just a sub - but based on reading this whole thread - am leaning towards not doing the kick panels and getting a 500.1 to go along with the sub. I think I can mount it where I mounted my relays for my compressor rather than mount to the roll bar. The slide out tailgate gives me a little extra room under the floor to mount it.

Mine is the regular, not shallow mount. Fits fine.

 

[SCTWNB]

@Ksjrb03 Excellent write up thank you for convincing me to spend more money - the speaker companies should be giving you a commission.

Quick point of clarification as I see some have mentioned the CWR84 and the CWRT84 (shallow mount) did you go with the standard or the shallow mount - and thoughts on the difference given the small enclosure for B&O?

I was likely going to do all speakers and just a sub - but based on reading this whole thread - am leaning towards not doing the kick panels and getting a 500.1 to go along with the sub. I think I can mount it where I mounted my relays for my compressor rather than mount to the roll bar. The slide out tailgate gives me a little extra room under the floor to mount it.

This speaker was used. Also, make sure you seal the port based on the speaker specs and add a little polyfil. https://www.crutchfield.com/p_20648CR84/Kicker-48CWR84.html

 

[Agrod]

I went ahead and got a Kicker Key 500 and a Kicker 12 inch down firing sub off Crutchfield. The audio store I went only had 0 gauge wiring kits in stock (overkill for this application). The cabling was pretty straight forward thanks to the info in this thread. The 0 gauge wire comes to a fused distribution block behind the access panel on the drivers side where a 8 gauge wire goes to the amp.

I cut the four cables that go to the factory sub and used a donor RCA cable to feed the signal into the amp. I wrapped it all in Tesa tape and ran it behind the factory sub. I’m thinking of adding an A/B switch behind the access panel in the passengers side to be able to turn off the Kicker amp and use the factory sub (or both at the same time).

I tucked the amp next to the factory sub and yolo’ed it with TEK screws to the body. I had to reroute the cable for the tail light and taped it to other wires so it wouldn't rattle.

I wanted to install the remote amp volume knob in the center console, but ran out of cable. I ended up drilling a hole into the headlight switch and installing the knob there.

The bass roll-off is really noticeable, bass response is not the best and it lacks punch (kick drums are non-existent, for example). I did however forget to run the Kicker Key signal processing tones, so I’ll have to take off the passengers side panel again to press the Key button and make any adjustments. I also forgot to snap a pic after installing the factory sub and cleaning everything. Hopefully I’ll have time next week to follow-up with nicer pics.

 

[aham23]

i just want to say this thread is why the internet can be great. so much great information and help. nice work all!

 

[Shawnj73]

First, this is one of the best write ups that I have read.


So, I have and hate the B&O System in my Bronco. This system is awful. I have dealt with it for a year now and I am ready to upgrade. I was wondering what options I will lose if I replace the B&O AMP completely? Is there a harness to run two amps for using factory wiring. I am aware that I will need to run Power and Ground for both amps. Also, will I need a separate DSP if I change the complete B&O amplifier?

I would like to use the factory area for sub. So the 8” Kicker upgrade, and all the B&O factory enclosure mods sounds like a winning solution. Does Kicker Key mono amp produce enough power to really drive the 8” woofer? I have not decided on amps yet so mounting locations are still up in the air. I am really trying to avoid mounting them under the seats, and I hate to give up any real estate in the cargo area.

for my system, I would like to use as much of the factory wiring as possible, and make it look as factory as possible. I know that this does not fix the sound stage, but upgrade needs to sound good and clean.

Lastly, for the dash speakers. I was thinking of replacing the dash left and right speakers with just tweeters and replace the center channel speaker with an Infinity. I have had good luck with Infinity over the years. Has anyone done this, I really think this would drastically improve the lacking highs. I was also thinking that I would 3D print a custom tweeter mount and mount the tweeter on top of the factory B&O grill, slightly angled up and towards the passenger and driver.

I did change the factory PODs out already. I added dynamat and 6 1/2" Infinity Kappas to the new bigger pods, this alone made a big difference to the soundstage, but just cannot deal with lack of Highs and Base any longer.

Help please, not looking for a thumping system, but something that sounds crisp and clean with matched base. Thanks for reading my ideas, open to any suggestions.

 

[Ksjrb03]

First, this is one of the best write ups that I have read.


So, I have and hate the B&O System in my Bronco. This system is awful. I have dealt with it for a year now and I am ready to upgrade. I was wondering what options I will lose if I replace the B&O AMP completely? Is there a harness to run two amps for using factory wiring. I am aware that I will need to run Power and Ground for both amps. Also, will I need a separate DSP if I change the complete B&O amplifier?

I would like to use the factory area for sub. So the 8” Kicker upgrade, and all the B&O factory enclosure mods sounds like a winning solution. Does Kicker Key mono amp produce enough power to really drive the 8” woofer? I have not decided on amps yet so mounting locations are still up in the air. I am really trying to avoid mounting them under the seats, and I hate to give up any real estate in the cargo area.

for my system, I would like to use as much of the factory wiring as possible, and make it look as factory as possible. I know that this does not fix the sound stage, but upgrade needs to sound good and clean.

Lastly, for the dash speakers. I was thinking of replacing the dash left and right speakers with just tweeters and replace the center channel speaker with an Infinity. I have had good luck with Infinity over the years. Has anyone done this, I really think this would drastically improve the lacking highs. I was also thinking that I would 3D print a custom tweeter mount and mount the tweeter on top of the factory B&O grill, slightly angled up and towards the passenger and driver.

I did change the factory PODs out already. I added dynamat and 6 1/2" Infinity Kappas to the new bigger pods, this alone made a big difference to the soundstage, but just cannot deal with lack of Highs and Base any longer.

Help please, not looking for a thumping system, but something that sounds crisp and clean with matched base. Thanks for reading my ideas, open to any suggestions.

The kicker key amp I used is plenty powerful for a little 8" sub.

Sorry I know nothing about options of replacing the factory amp/dsp, not something I have any interest in. I know there are other threads on this forum about them though!

 

[jehines3]

KSR laid the groundwork for many of us to get comfortable with the B&O Upgrade. I've not swapped any speakers yet, as I wanted to address the soundproofing and sub rattles first. The panel removal instructions and new clips were helpful tips for this project. The stock sub, as delivered, is a rattle trap. It requires several areas of double adhesive and rubber busing to get rid of all the hard contact points.

Now that I've improved the stock sub tremendously, I'm ready to dive into the five 4" speakers.

Are the Hertz still seeming to be the best option for all five locations, or is there a better mix to produce the best sound?

 

[SCTWNB]

I used Hertz as they have they have a high SPL rating

 

[MitchWalters]

A big thank you for the write-up and all the additional input from everyone. I followed
Ksjrb03's recommendations and process. Only issue was self-induced by breaking one of the blue panel attachment pins/clips during disassembly and I could not locate any to buy. Still cannot find any. The difference in sound quality is amazing. I'm not an audiophile by any means, but I went from not using the system in the Bronco, to really enjoying it. Thanks again for all the guidance.

BTW: It took me 2 full days to complete the upgrade. That includes all new speakers, amp, volume control & sub, and sound proofing. It took me a couple hours to isolate and fix rattles.

 

[Terrymo606]

I started my overhaul of the B&O system a couple months ago, and finished buttoning it up this weekend. It’s been a long journey of trial and error, and parts returned or wasted, but I’m thrilled with the final results. I have contributed to many threads along the way, but wanted to consolidate it all into a completed build thread as I get many questions about what I’ve done.

I’ll start out with why I got started on this project. To put it bluntly, I think the B&O system is pretty bad for a “premium“ system. It’s pretty much lacking in every way, low power, muddy highs, boomy rattly bass, and really bad soundstage with most all of the sound coming from the windshield. The speakers are cheap, paper, and half of them are the same speakers used in the base system.

I would rate the system 4/10 stock, and 15/10 after upgrades. This rating is based solely on my expectations/experiences of a factory “premium” system with cost as a factor. From the factory it severely missed expectations, after upgrades it blows away my expectations, as it should. The sub kicks. I haven't had a system that can rattle the mirrors since high school. I won’t be rattling mirrors, but I could if I want

I will list the parts ”I” used. Wiring diagrams and shop manuals for removal/install are attached.

Parts

JL C1 4” - $99 pair x2
https://www.crutchfield.com/p_13699040/JL-Audio-C1-400x.html

JL C1 6.5” - $149 pair
https://www.crutchfield.com/p_13699042/JL-Audio-C1-650x.html

Focal ACX 4” - $109 pair
https://www.crutchfield.com/p_091ACX100/Focal-ACX-100.html

Kicker Comp R 8” 4ohm DVC sub - $89
https://www.amazon.com/gp/product/B08NFHJZNP/ref=ppx_yo_dt_b_asin_title_o02_s00?ie=UTF8&psc=1

Kicker Key 500.1 amp - $270
https://www.amazon.com/gp/product/B084HLH77B/ref=ppx_yo_dt_b_asin_title_o09_s00?ie=UTF8&psc=1

Kicker wired remote bass control - $39
https://www.amazon.com/gp/product/B08D3TVFBX/ref=ppx_yo_dt_b_asin_title_o08_s01?ie=UTF8&psc=1

right angle extension wire for bass control knob - $11
https://www.amazon.com/gp/product/B0793KZYXD/ref=ppx_yo_dt_b_asin_title_o03_s00?ie=UTF8&th=1

25’ 8guage copper amp wire - $25
https://www.amazon.com/gp/product/B079RZF94M/ref=ppx_yo_dt_b_asin_title_o08_s01?ie=UTF8&psc=1

8 gauge amp fuse/battery connector - $9
https://www.amazon.com/gp/product/B071ZZZK5W/ref=ppx_yo_dt_b_asin_title_o08_s01?ie=UTF8&th=1

8 gauge ring terminal for ground - $7
https://www.amazon.com/gp/product/B0747M3SYQ/ref=ppx_yo_dt_b_asin_title_o08_s00?ie=UTF8&psc=1

4“ speaker wire harness adapter - x3 - $12.99 each pair
search Amazon

Kilmat sound deadening sheets - $35
https://www.amazon.com/gp/product/B082Q2J2T4/ref=ppx_yo_dt_b_asin_title_o03_s00?ie=UTF8&psc=1

Total - $979.97

Dash Speakers

There are three 4” speakers in the dash. I used JL C1 for all three. I originally tried Focal ACX, but found them very “bright”. I ended up using the Focals in the rear pods and the JLs in the dash. This combination works great, as the bright Focal pods allow more rear fill, that was canceled out having Focals in the dash as well. This combination makes huge improvements to the overall soundstage, actually having some rear fill is an amazing improvement. Don’t skip the center channel! It’s is the workhorse up front, especially if you use surround mode.

Replacing these speakers is pretty straightforward, remove trim panel, unbolt speaker, attach harness adapter, reinstall. Shop manual attached if you need it. I highly suggest a nice set of panel removal tools so you don’t scratch up the plastic. I tossed some kilmat underneath each speaker, trying to make the hollow space underneath more of a pocket.

The center channel is a little tricky, you need to remove a screw on each side of the “accessory ready” bolt, remove that, then you can remove the speaker cover panel.

Kick Panel

I used JL C1s here as well. Honestly a 2 way speaker is not needed here in the kick panels. The DSP/amp filters out highs, this is a place you could cheap out a bit If you want. The C1s came with a trim ring mounting adapter that worked great. Crutchfield also sent a Metra adapter that I did not use, and also sent a wiring harness adapter that I did use, both free. I used Kilmat behind these speakers as well. Removing the panels is easy enough, but it’s kind of an awkward spot to work in. There is a foam section below the speaker housing you will need to make a slit in and feed the wiring through. Button everything up with zip ties. Shop manual attached.

Rear Pod Speakers

As mentioned before I used Focal ACX back here. They work great to provide some much needed rear fill. These are the easiest speakers to replace. Pop the cover off by squeezing both sides and it will pop right off. Unscrew speaker, install wiring harness, reinstall. I filled the entire cavity with kilmat again. Shop manual attached.

Sub/Amp

This is where things got interesting. I first tried to just swap the sub speaker, and long story short that was a huge fail. I tried two different subs. A $300 Rockford P3 that popped and clicked, underpowered to say the least. A $19 Pyle sub worked, but wasn’t much if any improvement over the stock sub. I took a pause here as life got busy. Then got re-interested by @cmcbronco and his great thread on installing the B&O sub enclosure on a base system. Lots of great info here.

https://www.bronco6g.com/forum/threads/b-o-sub-installed-on-base-bronco-…-sorta….37207/

I ended up going with a Kicker Comp R 4 ohm DVC sub and Kicker key 500.1 amp. I wired the sub parallel to get 2 ohm at the amp. The beauty of this amp is you can use the speaker wires going to the factory sub as high level inputs. This will also work for the power on, so no need to find a trigger on circuit. I called Kicker and confirmed the sub wires coming from the factory amp will work for high level inputs, no line output converter needed. They said this is exactly what this amp was designed for.

The Comp R sub fits the factory enclosure great, but you need to pry the plastic trim ring off with a screwdriver. No modification needed to the enclosure with this sub. Shout out to @SCTWNB for the great mounting location for the amp, I wouldn’t of thought of this location myself. It’s mounted to the roll bar, snugged in there next to sub enclosure. It is a bit tricky, but take your time, mark your holes, drill some pilot holes. Use double sided mounting tape to hold it up for install and cushion it from the body. If you plan to use this location pay close attention to where i have it, any higher and the PATS antenna mounted on the quarter panel will interfere. A right angle adapter is needed for the remote volume wire, which I installed under the HVAC controls. Wire runs down the passenger side wire channel, up kick panel, behind glovebox.

I ran 8 gauge power wire across the cargo area behind rear seats, down floor wiring panels under door, up front kick panels, and through grommet in the firewall. Fused at battery, and connected to one of the spare spots Ford gave us. Need an M5 or M6 nut here, depending which you use. Ground is wired To the factory ground found right above sub. I cut the factory sub wires that are sealed in the grommet in sub enclosure, and connected them to the high level inputs on the amp. Cut off the RCA ends, and connected them with butt connectors, make sure you get polarity correct! Wiring drawing below. I drilled holes in the same grommet to run 14g speaker wire to the sub. Apologies for the lack of installation pics on most of this, I will grab some and update later if needed.

I ended up stuffing the enclosure with PolyFil. This really helped, the bass is less boomy, hits harder and tighter if that makes sense. I had to re-adjust my preferred settings afterwards, it makes a difference. Someone that doesn’t want to bother with a sub/amp should try adding polyfil to the oem sub. I bet it helps alot.

Rattle Battle

Anyone with the B&O system knows the sub is a rattle machine at higher volumes. I had the rear panels off no less than 5 times prior to upgrade finding and fixing rattles. I had my doubts if it could ever be rattle free with an aftermarket sub and amp. I am declaring 98% victory on rattles. For my everyday listening music and volumes it’s 100% victory.

I did so much fighting rattles it’s impossible to remember and list it all. My method was simple, play certain 90s gangsta rap songs with repeated bass frequencies on loop that generate rattle everytime. Loud. When neighbors were out that turned to bass frequency sweeps and loops I found online. Play loud and go around using your ears to pinpoint and your hands to feel and absorb. What I ended up with is Kilmat in the entire cargo area, 3 rolls of cloth tape wrapping wires, connectors, insulating behind pins, wiring under rear seats, etc. Used Kilmat to insulate behind most things touching the body. Suspect panel clips were replaced (and several broken). Be diligent in your battle and you can win!

Panel clips and part #s

Wiring drawing

11/14/22 Edit to add modified drawing, showing wire changes color after the green connector

Shop Manuals for removing trim

I have seen a few comments and videos on YouTube where people were using bass blockers. Getting ready to install this system I have the b&o system. I have everything ordered should I install bass blockers? Thanks

 

[Ksjrb03]

I have seen a few comments and videos on YouTube where people were using bass blockers. Getting ready to install this system I have the b&o system. I have everything ordered should I install bass blockers? Thanks

No, not needed on B&O

Sponsored