The tire pressure warning setting can be changed in the non-as built areaPlease, enlighten me
Sponsored
The tire pressure warning setting can be changed in the non-as built areaPlease, enlighten me
I tried it didn’t workI use the F-150 spreadsheet from 2019 onward to accomplish the DRL change
i coldn't figure it outI use the F-150 spreadsheet from 2019 onward to accomplish the DRL change
How'd this go for you? I checked Marketplace and somebody just happened to have the 10A (non-pro) model for $50. I'm thinking of using high-strength Velcro and mounting it to the top of the fusebox, tucked under the fender a bit. Definitely close to the hood, gonna try charging an old battery in the basement to see how warm the unit getsI'm in the middle of installing a hardwired 10A NOCO charger/maintainer in mine, along with an external plug adapter that also powers the block heater. Might be a good idea if you're going to bypass the battery protection, better than popping the hood open every time you park.
I mounted mine with an unused steel bracket from a bumper kit between the radiator and airbox, it's a one-off installation. The setup works great in all regards, and the plug being on the bumper takes all the hassle out of hooking up a trickle charger. I used the block heater for one night just to make sure everything was good, and then disconnected it (there's really no need for it where I live most days).How'd this go for you? I checked Marketplace and somebody just happened to have the 10A (non-pro) model for $50. I'm thinking of using high-strength Velcro and mounting it to the top of the fusebox, tucked under the fender a bit. Definitely close to the hood, gonna try charging an old battery in the basement to see how warm the unit gets
Yeah, still weighing my options. Didn't even look at the passenger side yet since it'll be plugged in from drivers side. On top of the fusebox seemed like the most open area, I'll have to look by the airbox. I was certainly surprised with the size, much bigger than the 1.5amp I have in my Flex.I mounted mine with an unused steel bracket from a bumper kit between the radiator and airbox
I don't know if the velcro would work for you though, if the charger is the same weight as mine. I'd consider a few zipties somewhere at least.
The leads were pretty long and I figured rather than coiling them up I'd use all that length. I paid for it all, I'm gonna use it all LOL I also have hood lift struts, so that really cuts down on the places I could put it, otherwise I would've stuffed it into the fender area.Yeah, still weighing my options. Didn't even look at the passenger side yet since it'll be plugged in from drivers side. On top of the fusebox seemed like the most open area, I'll have to look by the airbox. I was certainly surprised with the size, much bigger than the 1.5amp I have in my Flex.
I was always planning on backup zipties, but maybe I'll have to fab up something using random chunks of metal I have laying around. That or have the guys at work weld me something out of stainless steel.
Might put a male end mounted somewhere in the bumper, too. Most important thing is to tether the extension cord in some way that my wife can't forget to unplug it -- cut the cord short enough that she can't walk to the door without unplugging it like a velvet rope
Welcome to the club of no resolveHas anyone been able to change the zone lighting (side mirror lights) to stay on over 5mph? These would be great additional ditch lighting.
Welcome to the club of no resolve
At this point I think it's probably going to be easier to disconnect the OEM switch/power supply and use the switches as a trigger for a separate relay instead. You might lose the ability to control zone lighting from the display or remotely though. What I don't know is how much voltage and current they'd be able to support, as it appears from the wiring schematic that they only ground a signal wire. That could mean they support 1A@12V or it could mean they can only handle 5V/100mA. Will keep digging around to see what kind of info I can find.
I know, it would be a fantastic feature to have and I probably wouldn't be buying Oracle's mirror lights if I could use them for what I wanted. Somewhere in there is a way to change that programming, but it's way beyond my ability.Thank you for the reply! I just think that would be a cool feature to have them on at higher speeds when driving on the trail. It's like completely sideways ditch lights.
That’s just found in normal settings.. no need for Forscan to turn that off. Should be “settings“, “Vehicle” “Rear Occupant alert -off“ if I remember correctly. I also believe I read in the manual or somewhere that it has to be deselected every 6 months or something like that.Sorry if this question is covered somewhere but I tried using the advanced search to target this forum and didn't get a hit. Has anyone found the ForScan edit that will disable the chime for the "Check Rear Seats" everytime you shut off the vehicle?
Doubt that feature will work considering the bronco doesn’t have memory mirrors.Was playing around in ForScan while turning on my fogs and saw the tilt mirrors in reverse option.. I enabled that but it didn't work.. do I need to find another line to edit or does this just not work in the Bronco?